Rohde & Schwarz SME02 - Page 433

SME List of Commands
1038.6002.02 8C.3 E-12
Command
Parameter
SCPI
info
Page
[:SOURce]:AM:INTernal:FREQuency 400 Hz | 1 kHz | 3 kHz | 15 kHz or
0.1 Hz to 500 kHz or 0.1 Hz to1 MHz
3.31
[:SOURce]:AM:POLarity NORMal | INVerted not-SCPI 3.31
[:SOURce]:AM:SOURce EXT | INT1|2 | EXT, INT1|2 3.31
[:SOURce]:AM:STATe ON | OFF 3.31
[:SOURce]:CORRection[:STATe] ON | OFF 3.32
[:SOURce]:CORRection:CSET:CATalog? not-SCPI 3.32
[:SOURce]:CORRection:CSET[:SELect] ’Name of table’ not-SCPI 3.32
[:SOURce]:CORRection:CSET:DATA:FREQuency 5 kHz to 1.5/2.2/3/6 GHz
{,5 kHz to 1.5/2.2/3/6 GHz}
not-SCPI 3.33
[:SOURce]:CORRection:CSET:DATA:POWer -40dB to 6dB {,-40dB to 6dB} not-SCPI 3.33
[:SOURce]:CORRection:CSET:DELete ’Name of table’ not-SCPI 3.33
[:SOURce]:DM:MGRoup? not-SCPI 3.35
[:SOURce]:DM[:BASic]:TYPE GMSK | GFSK | QPSK | FSK | FSK4 |
FFSK
not-SCPI 3.36
[:SOURce]:DM[:BASic]:STATe ON | OFF 3.36
[:SOURce]:DM[:BASic]:SOURce EXTernal | PRBS | DATA 3.36
[:SOURce]:DM[:BASic]:CLOCk:MODE BIT | SYMBol not-SCPI 3.36
[:SOURce]:DM[:BASic]:CLOCk:POLarity NORMal | INVerted not-SCPI 3.36
[:SOURce]:DM[:BASic]:CLOCk:SOURce INTernal | COUPled not-SCPI 3.37
[:SOURce]:DM[:BASic]:DATA:CATalog? not-SCPI 3.37
[:SOURce]:DM[:BASic]:DATA:DELete ’Name’ not-SCPI 3.37
[:SOURce]:DM[:BASic]:DATA:DELete:ALL not-SCPI 3.37
[:SOURce]:DM[:BASic]:DATA:FREE? not-SCPI 3.37
[:SOURce]:DM[:BASic]:DATA:SELect ’Name’ not-SCPI 3.37
[:SOURce]:DM[:BASic]:DATA:DATA 0 | 1 {, 0 | 1} not-SCPI 3.38
[:SOURce]:DM[:BASic]:DATA:DATA:POINts? not-SCPI 3.38
[:SOURce]:DM[:BASic]:DATA:ATTenuate 0 | 1 {, 0 | 1} not-SCPI 3.38
[:SOURce]:DM[:BASic]:DATA:ATTenuate:POINts? not-SCPI 3.38
[:SOURce]:DM[:BASic]:DATA:BURSt 0 | 1 {, 0 | 1 not-SCPI 3.38