Siemens SIMODRIVE 611 universal - Page 923

E
E-923
 Siemens AG 2005 All Rights Reserved
SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition
Position–related switching signals (cams),
6-375
Positioning mode, 6-416
Positioning monitoring, 6-385
Power module, 1-30, A-856
Automatic identification, 4-137
Code, 4-138, A-856
Currents, A-856
Pulse frequency, A-856
Power–up inhibit, 4-135, 5-215
POWER-ON RESET on the front panel,
1-38
PPOs, 5-207
Pre–control, 6-379
Process data in the n-set-mode, 5-217,
5-219
Control words
DAU1, 5-217, 5-225
DAU2, 5-217, 5-225
DezEing (from SW 4.1), 5-227
DIG_OUT (from SW 3.1), 5-217,
5-226
G1_STW (from SW 3.1), 5-217, 5-243
G2_STW (from SW 3.3), 5-217, 5-243
G3_STW (from SW 3.1), 5-217, 5-243
KPC (from SW 4.1), 5-217, 5-224
MomRed, 5-217, 5-224
MsollExt (from SW 4.1), 5-217, 5-227
NSOLL_A, 5-217, 5-223
NSOLL_B (from SW 3.1), 5-217,
5-223
nsoll-l, 5-223
SatzAnw, 5-217
SatzAnw (from SW 4.1), 5-229
STW1, 5-217, 5-220
STW2, 5-217, 5-222
XERR (from SW 4.1), 5-217, 5-224
XSP (from SW 4.1), 5-217, 5-226
Status words
ADU1, 5-219, 5-236
ADU2, 5-219, 5-236
AktSatz (from SW 4.1), 5-219, 5-240
Ausl, 5-219, 5-237
DIG_IN (from SW 3.1), 5-219, 5-237
G1_XIST1 (from SW 3.1), 5-219,
5-243
G1_XIST2 (from SW 3.1), 5-219,
5-243
G1_ZSW (from SW 3.1), 5-219, 5-243
G2_XIST1 (from SW 3.3), 5-219,
5-243
G2_XIST2 (from SW 3.3), 5-219,
5-243
G2_ZSW (from SW 3.3), 5-219, 5-243
G3_XIST1 (from SW 3.1), 5-219,
5-243
G3_XIST2 (from SW 3.1), 5-219,
5-243
G3_ZSW (from SW 3.1), 5-219, 5-243
IqGl (from SW 3.1), 5-219, 5-239
MeldW, 5-219, 5-236
Msoll, 5-219, 5-238
nist–l, 5-235
NIST_A, 5-219, 5-235
NIST_B (from SW 3.1), 5-219, 5-235
Pwirk, 5-219, 5-238
VDClink (from SW 8.3), 5-219, 5-241
XistP, 5-242
ZSW1, 5-219, 5-233
ZSW2, 5-219, 5-235
E Index
04.05