EasyManua.ls Logo

Siemens SIMODRIVE 611 universal - Page 924

Siemens SIMODRIVE 611 universal
930 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
E
E-924
Siemens AG 2005 All Rights Reserved
SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition
Process data in the pos mode, 5-217, 5-219
Control words
DAU1, 5-217, 5-225
DAU2, 5-217, 5-225
DezEing (from SW 4.1), 5-217, 5-227
DIG_OUT (from SW 3.1), 5-217,
5-226
dXcorExt (from SW 4.1), 5-217, 5-231
MDIAcc (from SW 7.1), 5-217, 5-232
MDIDec (from SW 7.1), 5-217, 5-232
MDIMode (from SW 7.1), 5-218,
5-232
MDIPos (from SW 7.1), 5-217, 5-231
MDIVel (from SW 7.1), 5-217, 5-232
MomRed, 5-217, 5-224
Over, 5-217, 5-230
PosStw, 5-217, 5-230
QStw (from SW 4.1), 5-217, 5-228
SatzAnw, 5-217, 5-229
STW1, 5-217, 5-221
STW2, 5-217, 5-222
Xext (from SW 4.1), 5-217, 5-231
Status words
ADU1, 5-219, 5-236
ADU2, 5-219, 5-236
AktSatz, 5-219, 5-240
Ausl, 5-219, 5-237
DIG_IN (from SW 3.1), 5-219, 5-237
dXcor (from SW 4.1), 5-220, 5-242
IqGl (from SW 3.1), 5-219, 5-239
MeldW, 5-219, 5-236
Msoll, 5-219, 5-238
nist–l, 5-235
NIST_A, 5-235
NIST_B, 5-235
PosZsw, 5-219, 5-241
Pwirk, 5-219, 5-238
QZsw, 5-239
QZsw (from SW 4.1), 5-219
UZK1 (from SW 8.3), 5-219, 5-241
XistP (from SW 3.1), 5-219, 5-242
XsollP (from SW 4.1), 5-220, 5-242
ZSW1, 5-219, 5-234
ZSW2, 5-219, 5-235
PROFIBUS-DP
Commissioning, 5-285
Diagnostics and troubleshooting, 5-289
Encoder interface (from SW 3.1), 5-243
Evaluating faults, 5-290
Evaluating warnings, 5-291
Example: Operate drive, 5-271
Example: Reading parameters, 5-277
Example: Write parameter, 5-279
PZD configuring (from SW 3.1), 5-255
Setting the address, 5-287, 5-288
Switch out the DP slave (module), 5-305
Terminals and signals, 5-212
When can the modules be used?, 1-42
Which modules are available?, 1-32,
1-41
PROFIdrive conformance, 5-201
Pulse enable, 6-473
Pulse frequency, A-856
PZD area, 5-206, 5-216
Q
Qualified personnel, xi
R
Rack, 6-354
Ramp–function generator, 6-334
Ramp–up, 4-119
Ratio, 6-354
Read/write protection, 4-131
Reference cams, 6-391
Reference point approach, 6-389
References, C-897
Referencing/adjustment, 6-389
Reformatting, 6-411
Reformatting the memory, 6-411
Resolution, resolver, A-888
Resolver resolution, A-888
Revisions, vii
E Index
04.05

Table of Contents

Related product manuals