E
E-925
Siemens AG 2005 All Rights Reserved
SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition
Rotary axis
Axis coupling for modulo-rotary axes
(from SW 4.1), 6-448
with modulo correction (from SW 2.4),
6-355, 6-357, 6-358, 6-359, 6-416,
6-417
without modulo correction, 6-355, 6-356
Rotor position identification, 4-159, 4-178,
6-615
Rotor position synchronization, 6-615
RS232, 2-85, 3-105
RS485 (from HW ...1), 2-86, 3-106
S
Safe start inhibit, 1-33, 2-72
Safe stop, 1-33
Save data, 4-131
Serial interface
Cable diagram for RS232, 2-85
Cable diagram for RS485, 2-86
Changing–over, 3-104
Pin assignment, 2-83
Servo control, 6-603
Seven–segment display, 1-38
Shield connection, 2-68
Shielding, 2-66
Signal selection list for analog output, 6-546
SimoCom U
Entry in, 3-98
Information on, 3-99
Installing/un–installing, 3-97
Integrated help, 3-103
Optimum version, 3-96
via PROFIBUS-DP, 3-109
via serial interface, 3-103
SIMODRIVE 611 system
Components, 1-31
Integrating ”SIMODRIVE 611 universal”,
1-28
SIMODRIVE 611 universal, 1-24, 1-32
Applications, 1-26
Features, 1-32
Function overview, 1-27
System overview (schematic), 1-30
SIMODRIVE 611 universal E, 1-43
Control elements, 1-52
Features, 1-43
Front panel, 1-45
Terminals and interfaces, 1-46
What is different with respect to
SIMODRIVE 611 universal?, 1-55
Slave–to–slave communications (from SW
4.1), 5-314
Slave-to-slave communications (from SW
4.1), 5-314
Software limit switches, 6-372
Speed Controller, 6-332
Adaptation, 6-338
Automatic setting, 6-336
Optimization, 6-336
Speed controller at its endstop, 6-343
Speed controller output limited, 6-343
Speed pre–control, 6-379
Spindle positioning (from SW 5.1), 6-420,
6-605
Stall torque reduction factor, 6-349
Standstill monitoring (zero–speed monito-
ring), 6-383
Star/delta operation, 6-580
Start inhibit, 1-33
Stop responses, 7-622
Support, v
Suppress block, 6-416
SW limit switches, 6-372
Switch S1
on the control board, 1-39
on the supply infeed module, 2-69
System overview (schematic), 1-30
T
Teach–in (from SW 4.1), 6-601
Technical Support, v
Terminals
T. 15, 2-75
T. 16.x/15, 2-75
T. 19, 2-73
T. 24.x/20.x, 2-76
T. 65.x/14.x, 2-76
T. 65.x, 2-76
T. 663, 2-73
T. 75.x/15, 2-75
T. 9, 2-73, 2-76
T. I0.x to I3.x, 2-76, 6-474
T. I4 to I11, 2-79, 6-526
T. O0.x to O3.x, 2-77, 6-499
T. O4 to O11, 2-79, 6-526
Term. AS1/AS2, 2-72
Term. P24/M24, 2-73
Terminating resistor
for angular incremental encoder interface
as input (from SW 3.3), 1-39, 6-565
for RS485, 1-39, 3-107
04.05
To Next Page
Loading...
