Siemens SINAMICS G120C DP User Manual

A.1.4 Firmware version 4.7 SP9
Table A-4 New functions and function changes in 󹪝rmware4.7 SP9
 Function SINAMICS 
  G120 G120D
 
*0
*&
&83
&8%
&8(
&86
&8'
&8'
(7SUR)&
1 Support of PM240‑2 FSG Power Modules - - ✓ ✓ ✓ ✓ - - -
2 Support of PM240‑2 Power Modules in push-through technology, frame
sizes FSD… FSF, for the following voltages:
• 3 AC200V…240V
• 3AC380V…480V
• 3AC500V…690V
- - ✓ ✓ ✓ ✓ - - -
3 Shortened switch-on time for PM330 Power Modules - - ✓ - - - - - -
4 Expansion of the support for 1FP1 synchronous-reluctance motor with the
following converters:
• SINAMICS G110M
• SINAMICS G120D
• SINAMICS G120 with CU240B‑2 or CU240E‑2 Control Unit
A PM240‑2 Power Module is required to operate a 1FP1 synchronous-reluc‐
tance motor with SINAMICS G120
✓ - ✓ ✓ ✓ - ✓ - -
5 Support of 1FP3 synchronous-reluctance motors
A PM240‑2 Power Module is required to operate a 1FP3 synchronous-reluc‐
tance motor along with a selective release from SIEMENS
- - ✓ - - - - - -
6 Support of 1LE5 induction motors - ✓ ✓ ✓ ✓ ✓ - - -
7 The converter supports forming of the PM330 Power Module DC link capac‐
itors
- - ✓ - - - - - -
8 Setting option for two output reactors using parameter p0235 at the SI‐
NAMICS G120C and SINAMICS G120 with PM240-2 FSD … FSF Power Module
- ✓ ✓ ✓ ✓ ✓ - - -
9 E󹪟ciency-optimized operation of induction motors
Improved method "E󹪟ciency optimization2"
✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
10 New setting option for the "Technology application" p0500 = 5 during quick
commissioning
✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
11 Expansion of the available PROFIdrive telegrams in the SINAMICS G120C to
include telegram 350
- ✓ ✓ ✓ ✓ ✓ - - -
12 An SSI encoder can be parameterized as motor encoder - - - - - ✓ - ✓ -
13 Expansion of the "Basic positioner" function to include the feedback signal
from traversing blocks to the higher-level control system
- - - - - ✓ - ✓ -
14 Feedback signal supplemented to indicate that a memory card is not inser‐
ted in the converter:
• Parameter r9401 as BiCo parameter for the optional feedback signal to
the higher-level control system.
• New alarm A01101
✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
Appendix
A.1New and extended functions
SINAMICS G120C Converters
Operating Instructions, 02/2023, FW V4.7 SP14, A5E34263257B AK 453

Siemens SINAMICS G120C DP Specifications

General

Protection Rating	IP20
Frequency Range	0 to 650 Hz
Control Modes	V/f, sensorless vector control
Communication Interfaces	PROFIBUS DP
Ambient Temperature	-10 to +50 °C (without derating), -10 to +60 °C (with derating)
Overload Capacity	150 % rated current for 60 s, 200 % rated current for 3 s
Storage Temperature	-40 to +70 °C
Relative Humidity	5% to 95% (non-condensing)
Voltage Range	200 V to 240 V (±10%), 380 V to 480 V (±10%)
Output Voltage	0 V to Supply Voltage