Siemens Sinumerik 840D Series Function Manual

10.03
4.15 Parameters table
4-167
 Siemens AG, 2003. All rights reserved
SINUMERIK 840D/SIMODRIVE 611 digital, HLA Module (FBHLA) - 10.03 Edition
Max.
5008 5011 5012 5021
FLOAT UNS.WORD UNS.WORD WORD
Encoder phase error correction Actual-value sensing configuration Function switch Multi-turn resolution absolute value enc. in motor
4.10 4.10 4.12 4.10
immediately Power On immediately Power On
Degrees
HEX HEX
U
20.0
65535 65535
65535
0.0
0 4
0
-20.0
0 0
0000
ENC_PHASE_ERROR_CORRECTION ACTUAL_VALUE_CONFIG FUNC_SWITCH ENC_ABS_TURNS_MOTOR
1.01 1.01 1.01 1.01
5023 5024
DWORD
UNS.WORD UNS.WORD
5022 Measuring steps of absolute track in motor
Diagnosis meas. circ. motor abs. track Linear scale graduations
4.10 4.10 4.10
Power On immediately Power On
- -
nm
524287
BFFF
5000000
8192
0
20000
0000
0
1000
ENC_ABS_RESOL_MOTOR ENC_ABS_DIAGNOSIS_MOTOR DIVISION_LIN_SCALE
1.01 1.01 1.01
5100 5101
FLOAT FLOAT FLOAT5102
Modulus of elasticity of hydraulic fluid System pressure Pilot pressure
4.6 4.6 4.7
immediately Power On immediately
bar bar bar
21000
700.0 350.0
11000
0.0 0.0
1000
0.0 0.0
FLUID_ELASTIC_MODULUS WORKING_PRESSURE PILOT_OPERATION_PRESSURE
1.01 1.01 1.01
5001
UNS.WORDVelocity controller cycle 4.3.2Power On1642SPEEDCTRL_CYCLE_TIME 31.25 1.01
µ s
MD no. Name in NC Sec-
ware- Version
Unit
Attribute
Firm-
5106 5107 5108 5109 5110 5111 5112
UNS.WORD FLOAT FLOAT FLOAT FLOAT FLOAT FLOAT
Data type
Valve code number Nominal valve flowrate Nominal pressure drop of valve Nominal voltage of valve Knee-point flow rate of valve Valve flow ratio betw. A and B ends Knee-point voltage of valve
Index Active
4.7 4.7 4.7 4.7 4.7 4.7
immediately immediately immediately immediately immediately immediately immediately
-
l/min
bar
V % %
2000
1000.0
200.0
15.0 95.0
2.0
95.0
Version
0
0.0
35.0 10.0 10.0
1.0
10.0
Min.
0
0.0 1.0 0.5 0.2 0.5 0.2
VALVE_CODE VALVE_NOMINAL_FLOW VALVE_NOMINAL_PRESSURE VALVE_NOMINAL_VOLTAGE VALVE_DUAL_GAIN_FLOW VALVE_FLOW_FACTOR_A_B VALVE_DUAL_GAIN_VOLTAGE
Name in plaintext
1.01 1.01 1.01 1.01 1.01 1.01
5040
FLOATPiston zero in relation to machine zero 4.10immediatelymm100000.00.0 -1000000.0PISTON_ZERO 1.01
4.6 1.01
5002
UNS.WORDMonitoring cycle -Power On32003200 128MONITOR_CYCLE_TIME 1.01
5027 5041 5025 Serial number of motor measuring system
Configuration of encoder IM Machine zero in relation to actual position zero
4.10 4.10
-
Power On immediately
- -FFFFH
7FFFFFFF
0
0
0000H
-2147483647
1.02.04 1.02.04
1.01
SERIAL_NO_ENCODER MACHINE_ZERO_HIGH ENC_KONFIG
Power On
HEX
WORD
SIGN.DWORD
UNS.WORD
00
4294967295
5042
Machine zero in relation to actual position zero -immediatelyFFFFFFFF00
1.01
MACHINE_ZERO_LOW
HEX
UNS.WORD
5028
IM message frame length SSI 4.10-2525 0 1.02.04
NO_TRANSMISSION_BITS
Power On
WORD
5003 5005
WORD UNS.WORD
Configuration STS Encoder resolution for rotary measuring system
-
-
Power On Power On
HEX
-
07F0
65535
0330
2048
0
128
STS_CONFIG ENC_RESOL_MOTOR
1.01 1.01
5004
UNS.WORDConfiguration structure 4.3.1Power On10001000 0CTRL_CONFIG HEX 1.01
31.25
µ
s
tion
4 Firmware Drive Functions

Siemens Sinumerik 840D Series Specifications

General

Axes	Up to 31 axes
Power Supply	24 V DC
Control Type	CNC
Interface	Ethernet, PROFIBUS
Display	TFT color display
PLC	Integrated PLC (programmable logic controller)
Operating Temperature	0°C to 45°C
Relative Humidity	Up to 95% (non-condensing)
Max. Number of Channels	Up to 10 channels