TransTel Communications G1E+ - Program 05-19-IP: System Timing Parameters

To Next Page

To Previous Page

Program 05-19-IP : System Timing Parameters – 19

05-19-IP SYS PAR

0 0 0 0 0 0 0 0

IP = Item Pointer (01-08)

Value for each Item

IP Value Default Item Description

01 0- 0= Reserved

02 0- 0= Reserved

03 0- 0= Reserved

04 0-9 0=Disable VMU Silence Detection

05 0- 0=Australia Distinctive Ring Selection Australia or New Zealand

06 0- 0= Reserved

07 0- 0= Reserved

08 0- 0= Reserved

01. Reserved

02. Reserved

03. Reserved

04. VMU Silence Detection

This parameter enables Silence detection for the Voice Mail to disconnect a call after receiving this period of silence

from the caller.

IP \ Value 0 1 2 3 4 5 6 7 8 9 unit

05-19-04 Disable 10 20 30 40 50 60 70 80 90 sec.

05. Reserved

06. Reserved

07. Reserved

08. Reserved

Main Page

Notification2
Table of Contents3
Introduction13
- New Systems13
- Basic Programming Commands13
- Alphanumeric Entry14
- DK6 Key Telephone - Key Layout (36 Button)15
- DK6 Key Telephone - Key Layout (18 Button)15
Program 01-Tk-IP : Day Ringing and Ringing Line Preference Assignment16
Program 02-Tk-IP : Night Ringing and Ringing Line Preference Assignment16
Program 03-01-IP : Door Phone Ringing Assignment17
Program 04-Gp-IP : Console Operator Assignment17
Program 05-01-IP : System Timing Parameters - 0118
- Hold Recall Time18
- Exclusive Hold Recall Time18
- Hold Recall Timeout18
- DISA & ECF Access Delay Time - Day19
- Busy Remind Cycle Time (Off-Hook Ringing)19
- Pause Time19
- DTMF Generation Time19
- Call Forward no Answer Transfer Time19
Program 05-02-IP : System Timing Parameters - 0220
- SLT Dial Tone Timeout20
- SLT Inter-Digit Timeout20
- Auto Redial Access Time - PSTN Lines20
- SLT Release Signal Time20
- PSTN Line Flash Time - Key Phone & Analog Phone21
- SLT Hold Signal Time21
- Ring on Time21
- Ring off Time21
Program 05-03-IP : System Timing Parameters - 0322
- Make/Break Ratio22
- Automatic Trunk Search22
- Intercom Call Signalling Method22
- PABX (Centrex) Outgoing Code: (Refer to Program 35-TK-01)22
- Toll Access Code23
- Station Numbering Plan23
- Internal Dial Tone Pattern23
- Door Phone Ring Pattern23
Program 05-04-IP : System Timing Parameters - 0424
- System Baud Rate Setting24
- Dial 9 Flag24
- Action for Call Duration Limiting24
- 24 Hours Clock25
- SLT Hook Flash Answer Delay25
- Speed Dialing Distribution25
- Single Digit Intercom25
- SLT Message Waiting Method26
Program 05-05-IP : System Timing Parameters - 0527
- Wake up Call27
- Reserved27
- 03, 04. Speed Dial Unrestricted - 1, 227
- Name Function28
- Reserved28
- Auto Redial Attempts28
- Auto Redial Pause Time28
Program 05-06-IP : System Timing Parameters - 0629
- Transfer Busy Recall Time29
- Transfer Idle Recall Time29
- ISDN Audio Coding (A-Law Orμ- Law)29
- Polarity Reversal30
- Operator Code30
- Unsupervised Conference & ECF Time Setting30
- Hold Feature for SLT30
- Station Hunting Group - Ring Method30
Program 05-07-IP : System Timing Parameters - 0731
- Intercom Searching31
- Toll Override Prevention from Quick Dial31
- Paging Alert Tone31
- DISA Recall to Console - no Dialing31
- Key Phone Toll Override Prevention32
- SMDR Digit Mask32
- CO Line Guard Timer32
- Reserved32
Program 05-08-IP : System Timing Parameters - 0833
- Ring Hunt Time33
- DSS Access to Other Trunk Group33
- SLT Camp on Time33
- Console of DISA Transfer Group for no Answer34
- SLT Programming Digit34
- DISA Transfer Time no Answer34
- DISA Transfer Time - no Digits Dialed34
- Music Source Selection35
Program 05-09-IP : System Timing Parameters - 0936
- Console Queuing36
- Clear Forward Signal (Loop Disconnect) Detection36
- DISA Busy Tone Detection37
- Reserved37
- Enable Time37
- Segment 2 Recall Time37
- Release Time37
Program 05-10-IP : System Timing Parameters - 1038
Program 05-11-IP : System Timing Parameters - 1139
- DTMF Caller ID Leading Digit39
- Number of DISA Passwords39
- Select Music on Hold or Ring Back Tone39
- DISA & ECF Access Delay Time - Night39
- 05: DISA Special Function Access40
- DISA Re-Check Times to Station/Console40
- Door Phone Ringing Time40
- DISA Single Digit Dialing40
Program 05-12-IP : System Timing Parameters - 1241
- Call Transfer Method - Key Telephone41
- Reserved41
- Exclusive Hold Capability41
- Door Relay Activation Time41
- Voice Mail Call Forward Protocol Selection and Muting Leading Digits42
- Linear / Circular Trunk Group Access42
- LED Indication of Check in / Check out43
- Reserved43
Program 05-13-IP : System Timing Parameters - 1344
- Intercom Hot Key Dialing44
- Immediate SMDR Output44
- Caller ID Buffer Block Size44
- Reserved45
- Caller ID Record Storing Method for LCD Phones45
- CTI-Trunk Status Report45
- Least Cost Routing - Weekly Holiday 145
- Least Cost Routing - Weekly Holiday 245
Program 05-14-IP : System Timing Parameters - 1446
- SLT LCR Switch on Delay for PSTN46
- Reserved46
- DISA DTMF Detect Delay Time46
- CLI Delay Ring Time46
Program 05-15-IP : System Timing Parameters - 1547
- Company Greeting Time47
- ISDN FAX Protocol47
- Reserved48
Program 05-16-IP : System Timing Parameters - 1649
- Midnight Reset49
- Reserved49
- DISA Single Digit Dialing Level49
- VMU Language Service50
- Reserved50
- ACP Data Output Format50
Program 05-17-IP : System Timing Parameters - 1751
- Reserved51
- Voice Compression51
- Extension Number Announcement for DISA51
- DISA & ECF Access Delay Time - Lunch51
- DTMF Caller ID Leading Digits52
- DTMF CLI Trailing Digits52
- Call Block or Transfer to Voice Mail According to Caller ID Message52
- Minimum Mail Box Record Time53
Program 05-18-IP : System Timing Parameters - 1854
- Reserved54
- Hotel Alarm54
- Dial out History Feature54
- Caller ID Compatibility (Canada)55
- Reserved55
- Play Transfer Message for ECF55
- High Frequency Level of DTMF Generator55
- Low Frequency Level of DTMF Generator55
Program 05-19-IP : System Timing Parameters - 1956
- Reserved56
- VMU Silence Detection56
Program 05-20-IP : System Timing Parameters - 2057
- VMU Mailbox Delete All Messages57
- DISA no Digits Dialed (End of Message) Destination57
- Reserved57
Program 06-IP : Relay Assignment58
Program 07-Gp-IP : Flexible Key Group Assignment59
- DK6 - 18 Button Layout59
- DK6 - 36 Button Layout60
Program 08-Gp-IP : Flexible DSS Console Key Group Assignment62
Telephone Number63
Program 09-Nnn-DP : System Speed Dial63
Program 10-GP-IP : Intercom Single Digit Assignment64
Program 11-IP : Date and Time Setting65
Program 12-Nn : System Alarm Clock65
Program 13-Nn : Password66
Program 14-01-IP : SMDR Specifications67
- Call Duration Start Time67
- Record Incoming Calls67
- Record Local Calls67
- Record Incoming Calls no Answer67
- Print out the Title67
- Number of Records between the Title68
- Reserved68
- Polarity Reversal68
Program 17-Nn : Forced Account Code71
Program 18-Nn-TK : Assign Toll Plan to Trunk Lines72
Program 20-Nn- : Set Day - Time / Lunch Time Schedule73
Program 25 : Reset Data to System Default74
Program 29-Tk-IP : Trunk Specifications - 275
- Trunk Receive Gain75
- Function Enable75
- Trunk Transmit Gain75
- Set Ring Frequency (DK Handsets)76
- Allow Audible Ring for Incoming Calls76
- Polarity Reverse Detection - Individual Trunk-Outgoing76
- CO Delayed Ring Timer to Hunting Group76
- CO Delayed Ring Overflow Hunting Group76
Program 35-Tk-IP : Trunk Specifications - 177
- Trunk Type (CO / PABX)77
- Trunk Signal (Pulse / DTMF )77
- External Call Forward - ECF78
- DISA / ECF (Direct Inward System Access / External Call Forward)78
- Pick up78
- Loud Bell79
- Inward Line Ringing Method Assignment (Day)79
- Inward Line Ringing Method Assignment (Night)80
- Trunk Name Entry80
Program 36-Gp-Tk : Trunk Group Assignments81
Program 37-Tk : Busy out Trunks82
Program 38-Gp-Tk : Dial 87 Trunk Group Assignments83
Program 39-IP : Sensor Assignments84
Program 40-Stn-IP : Station Class of Service - 185
- Override Level85
- Monitor Level85
- 03: Limit Call Duration85
- Station Loud Bell86
- Access Paging86
- Receive Paging86
- Security Code Status86
- Forced Account Code86
Program 41-Stn-IP : Station Specifications87
- Station Group87
- Flexible Key Group Assignments for Key Phone87
- Shift Key Group for Key Phone87
- Dial 9 Trunk Group/ SLT Port as MOH Source88
- Toll Plan - Day88
- Toll Plan - Night88
- Port Number88
Program 42-Stn-IP : Register Memory Blocks for Individual Speed Dial89
Program 43-Cn-IP : Port Specifications90
- Station Number90
- Equipment Type90
- Flexible DSS Key Group Assignments for DSS Console91
- Reserved91
- Voice Mail Box Capacity-Virtual Mail Box91
- Maximum Message Length92
- Extension Name Entry92
Program 44-Stn-IP : Station Class of Service - 293
- System Alarm93
- Hold Feature93
- Call Split93
- Manual Line94
- Headset Feature94
- Use Engineering Password94
- Reserved94
- Station Alarm Signal94
Program 45-Stn-IP : Station Class of Service - 395
- Intercom Call Limitation95
- ACP Hear BGM at Idle State95
- Incremental Increase Ringing Volume95
- Allow Trunk Access95
- Intercom Calls to Different Station Groups96
- Receive Break Alarm96
- Allow Unrestricted Speed Dial Access96
- Record Station's SMDR Data96
Program 46-Stn-IP : Station Class of Service - 497
- Dial [87] Trunk Group97
- Message Waiting Level97
- Automatic Answer Capability (Keyphone) / Internal CLI (Caller ID) Function98
  - DISA/ISDN in Dial Recall Capability98
- Maximum Re-Transferred Times98
- Door Unlock / DND / CFWD Access98
- ACP Door Phone Hunt Group / Permanent Call Forward Group - no Answer99
- SLT Ring Cadence Settings99
Program 47-Stn-IP : Hot Line Assignment100
Program 48-Stn-IP : Station Class of Service - 5101
- Voice Mail Automatically Record Incoming Trunk Calls101
- Voice Mail Automatically Record Outgoing Trunk Calls101
- Group Listen Feature101
- Reserved102
Program 50-Stn-IP : Station Class of Service - 6102
- ACP Warning Signals102
- Call Forward Indication102
- ISDN Incoming Call Display Type-Digital Phone103
- CTI-Extension Status Report103
- VMS Leading Digits for Intercom Calls103
- ACP Door Unlock Relay103
- ACP Door Open Control103
- ACP Phone Operation / Hotel Alarm Type104
Program (51 to 59)-Code-IP : Toll Plans - Allowed Digits - Class 1 to 9105
Program (61 to 66)-Code-IP : Toll Plans - Restricted Digits - Class 1 to 6106
Program 67-Gp-IP : Hunt Group Pilot Number107
- Hunting Group Pilot Number107
- Hunting Group Ringing Method107
Program 68-Gp-IP : Hunt Group Assignment - Day108
Program 69-Gp-IP : Station Hunt Group Assignment - Night109
Program 70-CD-IP : ISDN Interface Specifications Program - G1E110
Program 71-CD-IP : Calling Line Identification Presentation111
Program 72-St : ISDN Called Party Extension Number Assignment112
Program 73-St : ISDN Extension Sub-Address Assignment112
Program 75-Num-IP : LCR - Analysis Table114
Program 76-Num-Tm : LCR - Routing Table115
Program 77-Num : LCR - Modifying Table116
Program 78-Stn-IP : Station Class of Service - 6117
- LCR Routing Level117
- LCR - Direct Access a Trunk117
- Reserved117
- Call Forward Busy Transfer Group118
- External Notification - Voicemail118
- ISDN Calling Line Identification Presentation118
- Ringing Line Preference118
- Reserved118
Program 83-St-IP : Register Memory Block for CLI History Buffer119
Program 84-IP : Home Area Code120
Program 85-Nn-IP : Overlay Area Code120
Program 86-Nnn-IP : Office Code Redial Pattern121
Program 87-CN-IP : ASSIGN DOOR PHONE for KEY CARD122
Program 88-DP : REGISTER KEY CARD123
Program 89-CN-IP : DELETE KEY CARD124
Program 91-TM : ACP TIME LOCK - Assign Time125
Program 92-CN : ACP TIME LOCK - Assign Card125
Program 93 : Not Used in North America126
Program 94-Tk-IP : Lunchtime Ringing and Ringing Line Preference Assignment127
Program 95-Tk-IP : Trunk Specifications - 3128
- Detect Fax Signal128
- Reserved129
- DISA & ECF Lunch Time Enable129
Programming Cross Reference130
- Incoming Calls130
  - Ringing Assignment130
- Outgoing Calls130
- Intercom Calls132
- Busy/During Conversation133
- DISA - Auto Attendant133
- Night Service134
- Group Assignments134
- Call Control135
- System Clock136
- Station Numbering136
- Single Line Telephone136
- Miscellaneous136
- Optional Services137
- DISA and Auto Attendant Operation139
  - Clear down of Unanswered Calls139
- Recording DISA Messages140
- DISA no Digits Dialed (End of Message) Transfer Location140
  - Programming Single Digit DISA141
- Installing Acp's141
  - About Security141
  - How Can I Use an ACP142

TransTel Communications G1E+ - Program 05-19-IP: System Timing Parameters - 19; Reserved; VMU Silence Detection

Table of Contents

Related product manuals