Unipulse F371 - Page 33

To Next Page

To Previous Page

4.CALIBRATION

4）Enter the rated output of the sensor by the numerical keys and determine with the OK

button. The decimal point is fixed.

5）Enter the rated value by the numerical keys and determine with the OK button.

Main Page

Default Chapter3
- Safety Precautions3
- Table of Contents5
1 ．Appearance Description12
- Front Panel12
  - Touch Panel Display12
  - Power Lamp12
- Rear Panel13
2 ．Setting Modes16
- F371 Screen Configuration16
- Setting Modes Tree17
- About a Setting Call19
3 ．Connection20
- Power Input Connection20
- Load Cell Connection21
- SI/F Connection22
- External I/O Connection23
  - External Output Connection23
  - External Input Connection23
- RS-232C Interface Connection24
- Voltage Output Connection25
  - Connecting to Cage Clamp Terminal Block26
4 ．Calibration27
- Equivalent Input Calibration Procedure28
- Actual Load Calibration Procedure29
- Zero Calibration30
- Actual Load Calibration31
- Equivalent Input Calibration32
- Digital Offset34
- Increment (this Step May be Omitted if There Is no Change.)35
- Decimal Place36
- Calibration Protection37
- Calibration Value Selection38
  - External Selection of Calibration Value39
- Unit40
5 ．Setting of Functions42
- Digital Zero42
- Digital Filter43
- Analog Filter44
- Display Rate44
- Stability45
- Zero Track46
- Contrast Adjustment47
- Backlight47
- Excitation Voltage47
- Auto Print48
- Hold off Print50
- Parameter Protection50
6 ．Comparison Functions51
- HI Limit/Lo Limit/Hi-HI Limit/Lo-LO Limit52
- Hysteresis53
- Near Zero55
- HI-LO Limit Comparison Mode55
- HI-LO Limit Output Mode56
- Alarm Mode57
7 ．Hold Functions58
- Hold Setting58
- Hold Setting61
  - Minimum Count62
  - Valley Detection Level62
- Hold Setting63
  - Minimum Slope64
  - Interval a and Interval B64
- Hold Setting66
  - Mean Value Sampling Count66
- Hold Operation67
- How to Specify the Hold Detection Period75
8 ．Multi-Hold Function79
- About Changing of the Setting CH80
9 ．Waveform Display81
- Graphic Display Screen81
  - Hold Point Plotting82
  - X-Axis and Y-Axis on the Graph Plotting Screen82
- Graph Plotting83
- Graph Function86
- Interval Time86
- Graph Start Level86
- Level Detection Mode87
- Start Point88
- Y (Load) Start Point and y (Load) End Point89
10 ．Voltage Output（Vol out90
11 ．Screen Lock91
12 ．Event Output at the End of Graph Plotting91
13 ．Rs-232C Interface92
- Communication Specifications92
- RS-232C Interface Setting94
- Communication Modes96
- Communication Format96
14 ．Bcd Data Output(Option)103
- Connector Pin Assignment103
- Logic Change104
- BCD Data Hold104
- Equivalent Circuit104
- Signal Timing105
- BCD Data Update Rate Selection106
- BCD Output Data Selection106
15 ．Rs-485 Communication Interface(Option)107
- Communication Specifications107
- Connection107
- Communication Method110
- Interface Setting111
16 ．D/A Converter(Option)112
- Voltage Zero and Full Scale, Current Zero and Full Scale113
- D/A Output Mode114
- Voltage Output Selection114
- Current Output Selection114
17 ．DC Power Source116
- Error Messages117
19 ．Self-Check and Initialization118
- Self-Check118
- Initialization(All Setting Value Clearances)120
- Password120
20 ．About Japanese/English Display Selection121
21 ．Block Diagram122
22 ．Dimensions123
23 ．Installation in a Panel124
24 ．Specifications125
- Analog Section125
- Digital Section125
- Communication126
- Options126
- External Input and Output127
- General128
- Accessories129
25 ．Setting Item Chart130
26 ．Conformity to Ec Directives134

Unipulse F371 - Page 33

Table of Contents

Related product manuals