Yamaha FZ09E - Page 51

TIGHTENING TORQUES
Item
Thr e ad
Q' ty Tighten i ng torque Remar ks
size
Intake air pressu re sensor screw M5
2
7 Nm (0.7 m·kgf, 5 .1 ft·lbf)
Stator coil bolt M6 3 14 Nm (1.4 m·kgf, 1
O ft·lbf)
-<J
Oil level switch bolt M6 2 1 O Nm (1 .0 m·kgf, 7.2 fl·lbf)
Starter motor bolt M6
2
12 Nm (1.2 m·kgf, 8.7 ft·lbf)
Starter motor lead nut M6 1 7 Nm (0.7 m·kgf,
5.1 ft·lbf)
Speed sens
or bo lt M6 1 1 O Nm (1.0 m·kgf, 7 .2 ft·lb f)
-<J
Shift rod locknut (front) M6 1 8 Nm (0.8 m·kgf, 5.8 ft·lbf)
Shift rod locknut (rear) M6 1 8 Nm (0.8 m·kgf, 5.8 ft·lbf)
Left
thread
Shift rod joint bolt M6 1 1
O Nm (1 .0 m·kgf, 7 .2 ft·lbf)
-<J
Adapter bolt (lefVright) M6 2 12 Nm ( 1. 2 m·kgf, 8.7 ft·lbf)
Oil
fi ller cap M20 1 1.5 Nm (0. 15 m·k gf, 1. 1 ft·lbf)
Starter motor assembly
bo lt M5 2 5 Nm (0.5m -k gf , 3.6 ft -lb f)
Starter motor insulator nut M6 1
11 Nm (1 .1 m·kgf, 8.0 ft·lb f)
Throttle position sensor s cr ew
M5 2 3.5 Nm (0.35 m·kgf, 2.5 ft·lbf)
Accelerat
or position sensor bolt M5 2 3.5 Nm (0.35 m·kgf, 2.5 ft-lbf)
Clutch cable and adjust nut
MS 1 7 Nm (0.7 m·kgf, 5 .1 ft·lbf)
Throttle cable and throttle body
M6 2 4.5 Nm (0.45 m·kgf, 3.3 ft·lbf)
Coolant reservoir
bo lt M5 1 0.5 Nm (0. 05 m·kgf, 0. 37 ft·lbf)
Coolant reservoir
bo lt
M6
1 9 Nm (0.9 m·k gf , 6.5 ft·lbf)
Radiator bolt M6 2 1
O Nm (1 .0 m-kgf, 7.2 ft- lbf)
Radiator fan cover bolt M6 1 7 Nm (0.7 m·kgf,
5.1 ft·lbf)
-<J
Radiator cap bolt
M5
1 5 Nm (0 .5 m·kgf, 3.6 ft ·l bf)
Radiator stay bolt M6 1 1
O Nm (1 .0 m-kgf, 7.2 ft- lbf)
TIP ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Camshaft cap bolt
Tighten the bolts to 10 Nm (1.0 m·kgf, 7.2 ft·lbl) follow in g the tightening or de r.
2-16