Digital Input Reading ............................................................23
Digital Operator Display Selection..................................... 161, 292
Digital Operator Keypad Functions .......................................... 162
Digital Output Card Settings ....................................................89
Digital Output Option Card Terminal Function Selection ..................89
dnE................................................................................ 205
DO-A3 Output Mode Selection.................................................89
DO-A3 Settings ...................................................................89
Drive/kVA Selection ........................................................... 292
Drive Capacity Setting Fault .................................................. 213
Drive Disabled .................................................................. 205
Drive Does Not Allow Selection of Rotational Auto-Tuning ............ 229
Drive Duty Mode Selection .....................................................57
Drive Model Mismatch ........................................................ 222
Drive Model Selection ......................................................... 163
Drive Mode Unit Monitor Selection ................................... 161, 292
Drive Operation Status at Previous Fault.................................... 301
Drive Overload.................................................................. 195
Drive Slave Address...................................................... 122, 319
Drive Status...................................................................... 299
Drive Transmit Wait Time .............................................. 123, 320
Drive Unit Signal Fault ........................................................ 186
DriveWorksEZ Connection Parameters ..................................... 166
DriveWorksEZ Custom Monitor 1 to 10 .................................... 306
DriveWorksEZ Fault ........................................................... 187
DriveWorksEZ Function Selection.............................................16
DriveWorksEZ Monitors ...................................................... 172
DriveWorksEZ Parameters .................................................... 166
Droop Control Delay Time ......................................................44
Droop Control Gain ..............................................................44
During Frequency Output Time Chart ....................................... 114
During Run Time Chart........................................................ 106
dv1 ................................................................................ 187
dv2 ................................................................................ 187
dWAL ............................................................................ 187
Dwell Function..............................................................43, 177
Dwell Reference at Start .........................................................43
Dwell Reference at Stop .........................................................43
Dwell Time at Start...............................................................43
Dwell Time at Stop ...............................................................43
DWEZ Version Control Monitor 1 to 3...................................... 306
dWFL............................................................................. 187
Dynamic Braking Transistor .................................................. 198
E
E1-08 ....................................................................... 176, 177
E1-09 ............................................................................. 227
E1-10 ....................................................................... 176, 177
E2-01 ............................................................................. 176
E2-02 ............................................................................. 176
E2-03 ....................................................................... 176, 218
E3-01 (Motor 2 Control Mode) Dependent Parameters ................... 308
E5 ................................................................................. 187
EEPROM Memory Data Error................................................ 185
EEPROM Write Error.......................................................... 188
EF ................................................................................. 205
EF0 ......................................................................... 188, 205
EF1 ......................................................................... 188, 206
EF2 ......................................................................... 188, 206
EF3 ......................................................................... 188, 206
EF4
......................................................................... 188, 206
EF5 ......................................................................... 188, 206
EF6 ......................................................................... 188, 206
EF7 ......................................................................... 188, 206
EF8 ......................................................................... 188, 206
EFAn ....................................................................... 187, 205
End................................................................................ 222
End1 .............................................................................. 217
End2 .............................................................................. 217
End3 .............................................................................. 217
End4 .............................................................................. 217
End5 .............................................................................. 217
End6 .............................................................................. 217
End7 .............................................................................. 218
Energy Savings Constants Error .............................................. 216
Enter Command................................................................. 124
Enter command necessary ............................................... 124, 321
Enter command not necessary .......................................... 124, 321
Enter Command Settings when Upgrading the Drive...................... 344
Enter Command Types......................................................... 344
Er-01.............................................................................. 218
Er-02.............................................................................. 218
Er-03.............................................................................. 218
Er-04.............................................................................. 218
Er-05.............................................................................. 218
Er-08.............................................................................. 219
Er-09.............................................................................. 219
Er-10.............................................................................. 219
Er-11.............................................................................. 219
Er-12.............................................................................. 219
Er-13.............................................................................. 220
Er-14.............................................................................. 220
Er-15.............................................................................. 220
Er-17.............................................................................. 220
Er-18.............................................................................. 220
Er-19.............................................................................. 220
Er-20.............................................................................. 220
Er-21.............................................................................. 221
Err................................................................................. 188
Error Reading Data ............................................................. 223
Errors and Displays When Using the Copy Function...................... 182
Error Writing Data.............................................................. 222
Excessive PID Feedback................................................. 189, 206
Excessive V/f Setting........................................................... 217
Exhaust Fan Application.........................................................15
External Digital Operator Connection Fault ................................ 196
External Fault ............................................................. 188, 206
External Fault from Comm. Option Detection Selection....................90
External Fault from Comm. Option Operation Selection ...................90
F
FAn ............................................................................... 188
FAn Alarm Location Monitor................................................. 304
Fast Stop Sequence ............................................................. 100
Fast Stop Time ....................................................................47
Fault Causes and Solutions .................................................... 184
Fault Detection .................................................................. 184
Fault Displays ................................................................... 184
Fault History............................................................... 171, 224
Fault Reset Interval Time................................................ 148, 286
Index
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual
349
To Next Page
Loading...
