YASKAWA A1000 HHP

PGo ......................................................................... 198, 210
PGoH ....................................................................... 198, 210
PG Open-Circuit Detection Time...............................................84
PG Option Card Disconnection Detection 1 ..................................86
PG Option Card Disconnection Detection 2 ..................................86
PG Option Card Port for Motor 2 Selection...................................86
PG Speed Control Card Settings................................................84
Phase Order Selection............................................................24
PID Accel/Decel Time ...........................................................41
PID Block Diagram...............................................................36
PID Control........................................................................33
PID Feedback ................................................................... 305
PID Feedback High Detection Level...........................................40
PID Feedback High Detection Time ...........................................40
PID Feedback Input Methods ...................................................34
PID Feedback Loss ....................................................... 189, 206
PID Feedback Loss Detection Selection.......................................39
PID Feedback Low Detection Level ...........................................39
PID Feedback Low Detection Time............................................40
PID Fine Tuning ..................................................................42
PID Function Setting .............................................................37
PID Input (feedback) ........................................................... 305
PID Input Limit ...................................................................41
PID Monitors .................................................................... 171
PID Offset Adjustment...........................................................38
PID Output....................................................................... 305
PID Output Gain Setting.........................................................38
PID Output Level Selection .....................................................38
PID Output Limit .................................................................38
PID Output Lower Limit.........................................................41
PID Output Reverse Selection ..................................................38
PID Primary Delay Time Constant.............................................38
PID Setpoint ..................................................................... 305
PID Setpoint Display Digits.....................................................42
PID Setpoint Input Methods.....................................................34
PID Setpoint Scaling .............................................................41
PID Setpoint Selection ...........................................................41
PID Setpoint User Display ......................................................42
PID Setpoint Value ...............................................................41
PID Sleep ..........................................................................40
PID Sleep Delay Time ...........................................................40
PID Sleep Function Start Level.................................................40
PM Inductance Error ........................................................... 220
Power Unit Output Phase Loss 3 ............................................. 190
Predefined V/f Patterns ..........................................................75
Preset Reference Timing Diagram .............................................61
Previous Fault ................................................................... 300
PROFIBUS-DP Clear Mode Selection ........................................92
PROFIBUS-DP Data Format Selection........................................92
PROFIBUS-DP Node Address .................................................92
PROFIBUS-DP Parameters .....................................................91
Proportional Gain Setting (P) ...................................................37
PTC ............................................................................... 120
PUF ............................................................................... 198
Pulse Monitor Selection Error ................................................ 216
Pulse Train Input/Output....................................................... 105
Pulse Train Input Bias.......................................................... 126
Pulse Train Input Filter Time ................................................. 126
Pulse Train Input Gain ......................................................... 126
Pulse Train Input Minimum Frequency...................................... 127
Pulse Train Input Scaling
...................................................... 126
Pulse Train Input Terminal RP Function Selection ........................ 125
Pulse Train Monitor Scaling .................................................. 127
Pulse Train Monitor Selection ................................................ 127
Q
q-axis ACR Output ............................................................. 305
R
Ramp to stop ......................................................................20
Rated Current Setting Alarm .................................................. 217
Rated Slip Error................................................................. 219
rdEr ............................................................................... 223
READ ............................................................................ 164
rEAd .............................................................................. 223
Reading Drive MEMOBUS/Modbus Register Contents .................. 326
Reading Parameter Settings ................................................... 223
Regenerative Torque Limit mode selection ................................. 288
Reset Communication Parameters..............................................91
Resistance Tuning Error ....................................................... 217
Response Messages from Drive to Master .................................. 323
Reverse Direction Output Example Time Chart............................ 112
Reverse Operation Selection ....................................................22
Reverse Prohibited Error....................................................... 220
Reverse Regenerative Torque Limit ................................... 151, 287
Reverse Torque Limit .................................................... 151, 287
rF.................................................................................. 198
rH ................................................................................. 198
rr................................................................................... 198
RS-422 Interface ................................................................ 317
RS-485 Interface ................................................................ 317
RTS Control Selection ................................................... 124, 320
rUn................................................................................ 210
Run Command/Frequency Reference Source Selection Error............ 214
Run Command at Power Up.....................................................25
Run Command Method Selection ...................................... 124, 321
Run Command Selection ...................................................... 227
Run Command Selection 1 ................................................19, 240
Run Command Selection 2 ......................................................25
Run command selection while in Programming Mode ......................24
Run Command Source Selection ............................................. 303
S
Safe Disable Signal Input................................................ 206, 207
SC................................................................................. 199
S-Curve Characteristics ........................................................ 177
SE ................................................................................. 211
Self-Diagnostics................................................................. 346
SEr ................................................................................ 199
Serial Communications Cable Connection Terminals (TB4) ............. 316
Serial Communication Transmission Error ................................. 204
Single Drive KEB Ride-Thru 1 ............................................... 135
Slave Address ................................................................... 324
Slip Compensation................................................................48
Slip Compensation Gain ...................................................48, 177
Slip Compensation Limit ........................................................49
Slip Compensation Primary Delay Time ................................49, 177
Slip Compensation Selection during Regeneration ..........................49
Soft Charge Bypass Relay Maintenance..................................... 302
Soft Charge Bypass Relay Maintenance Time.............................. 208
Soft CLA Selection............................................................. 288
Index
354
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual