E.3 User Setting Table
YASKAWA ELECTRIC SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual 429
E1-08 Middle Output Frequency Voltage
E1-09 Minimum Output Frequency
E1-10 Minimum Output Frequency Voltage
E1-11 Middle Output Frequency 2
E1-12 Mid Output Frequency Voltage 2
E1-13 Base Voltage
E2-01 Motor Rated Current
E2-02 Motor Rated Slip
E2-03 Motor No-Load Current
E2-04 Number of Motor Poles
E2-05 Motor Line-to-Line Resistance
E2-06 Motor Leakage Inductance
E2-07 Motor Iron-Core Saturation Coefficient 1
E2-08 Motor Iron-Core Saturation Coefficient 2
E2-09 Motor Mechanical Loss
E2-10 Motor Iron Loss for Torque Compensation
E2-11 Motor Rated Power
E2-12 Motor Iron-Core Saturation Coefficient 3
E3-01 Motor 2 Control Mode Selection
E3-04 Motor 2 Max Output Frequency
E3-05 Motor 2 Max Voltage
E3-06 Motor 2 Base Frequency
E3-07 Motor 2 Mid Output Frequency
E3-08 Motor 2 Mid Output Frequency Voltage
E3-09 Motor 2 Minimum Output Frequency
E3-10 Motor 2 Minimum Output Frequency Voltage
E3-11 Motor 2 Mid Output Frequency 2
E3-12 Motor 2 Mid Output Frequency Voltage 2
E3-13 Motor 2 Base Voltage
E4-01 Motor 2 Rated Current
E4-02 Motor 2 Rated Slip
E4-03 Motor 2 Rated No-Load Current
E4-04 Motor 2 Motor Poles
E4-05 Motor 2 Line-to-Line Resistance
E4-06 Motor 2 Leakage Inductance
E4-10 Motor 2 Iron Loss
E4-11 Motor 2 Rated Power
E4-14
Motor 2 Slip Compensation Gain
E4-15
Motor 2 Torque Compensation Gain
E5-01 PM Motor Code Selection
E5-02 Motor Rated Power
E5-03 Motor Rated Current
E5-04 Number of Motor Poles
E5-05 Motor Stator Resistance
E5-06 Motor d-Axis Inductance
E5-07 Motor q-Axis Inductance
E5-09 Motor Induction Voltage Constant 1
E5-24 Motor Induction Voltage Constant 2
F1-02 PG 1 Pulses Per Revolution
F1-03 Operation Selection at Overspeed (oS)
F1-04 Operation Selection at Deviation (dEv)
F1-08 Overspeed Detection Level
F1-09 Overspeed Detection Delay Time
No. Name
User
Setting
F1-10 Excessive Speed Deviation Detection Level
F1-11
Excessive Speed Deviation Detection Delay
Time
F1-14 PG Open-Circuit Detection Time
F6-01 Communications Error Operation Selection
F6-02
External Fault from Comm. Option Detection
Selection
F6-03
External Fault from Comm. Option Operation
Selection
F6-07
NetRef/ComRef Function Preselection
Capability
F6-08 Reset Communication Parameters
F6-10 CC-Link Node Address
F6-11 CC-Link Communications Speed
F6-14 bUS Error Auto Reset
F6-30 PROFIBUS-DP Node Address
F6-31 PROFIBUS-DP Clear Mode Selection
F6-32 PROFIBUS-DP Data Format Selection
F6-35 CANopen Node ID Selection
F6-36 CANopen Communication Speed
F6-50 DeviceNet MAC Address
F6-51 Device Net Communications Speed
F6-52 DeviceNet PCA Setting
F6-53 DeviceNet PPA Setting
F6-54 DeviceNet Idle Mode Fault Detection
F6-55 DeviceNet Baud Rate Monitor
F6-56 DeviceNet Speed Scaling
F6-57 DeviceNet Current Scaling
F6-58 DeviceNet Torque Scaling
F6-59 DeviceNet Power Scaling
F6-60 DeviceNet Voltage Scaling
F6-61 DeviceNet Time Scaling
F6-62 DeviceNet Heartbeat Interval
F6-63 DeviceNet Network MAC ID
F6-64 to
F6-71
Dynamic Assembly Parameters (Reserved)
H1-01
Multi-Function Digital Input Terminal S1
Function Selection
H1-02
Multi-Function Digital Input Terminal S2
Function Selection
H1-03
Multi-Function Digital Input Terminal S3
Function Selection
H1-04
Multi-Function Digital Input Terminal S4
Function Selection
H1-05
Multi-Function Digital Input Terminal S5
Function Selection
H1-06
Multi-Function Digital Input Terminal S6
Function Selection
H2-01
Terminal MA, MB and MC Function Selection
(relay)
H2-02
Terminal P1-PC Function Selection (open-
collector)
H2-03
Terminal P2-PC Function Selection (open-
collector)
H2-06 Watt Hour Output Unit Selection
H3-01 Terminal A1 Signal Level Selection
H3-02 Terminal A1 Function Selection
No. Name
User
Setting
To Next Page
Loading...
