E.3 User Setting Table
430 YASKAWA ELECTRIC SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual
H3-03
Terminal A1 Gain Setting
H3-04
Terminal A1 Bias Setting
H3-09 Terminal A2 Signal Level Selection
H3-10 Terminal A2 Function Selection
H3-11
Terminal A2 Gain Setting
H3-12
Terminal A2 Bias Setting
H3-13 Analog Input Filter Time Constant
H4-01
Multi-Function Analog Output Terminal AM
Monitor Selection
H4-02
Multi-Function Analog Output Terminal
AM Gain
H4-03
Multi-Function Analog Output Terminal AM
Bias
H5-01 Drive Node Address
H5-02 Communication Speed Selection
H5-03 Communication Parity Selection
H5-04
Stopping Method after Communication Error
(CE)
H5-05 Communication Fault Detection Selection
H5-06 Drive Transmit Wait Time
H5-07 RTS Control Selection
H5-09 CE Detection Time
H5-10
Unit Selection for MEMOBUS/Modbus
Register 0025H
H5-11 Communications ENTER Function Selection
H5-12 Run Command Method Selection
H6-01
Pulse Train Input Terminal RP Function
Selection
H6-02
Pulse Train Input Scaling
H6-03
Pulse Train Input Gain
H6-04
Pulse Train Input Bias
H6-05
Pulse Train Input Filter Time
H6-06
Pulse Train Monitor Selection
H6-07
Pulse Train Monitor Scaling
L1-01 Motor Overload Protection Selection
L1-02 Motor Overload Protection Time
L1-03
Motor Overheat Alarm Operation Selection
(PTC input)
L1-04
Motor Overheat Fault Operation Selection
(PTC input)
L1-05
Motor Temperature Input Filter Time (PTC
input)
L1-13
Continuous Electrothermal Operation
Selection
L2-01 Momentary Power Loss Operation Selection
L2-02 Momentary Power Loss Ride-Thru Time
L2-03
Momentary Power Loss Minimum Baseblock
Time
No. Name
User
Setting
L2-04
Momentary Power Loss Voltage Recovery
Ramp Time
L2-05 Undervoltage Detection Level (Uv1)
L3-01 Stall Prevention Selection during Acceleration
L3-02
Stall Prevention Level during Acceleration
L3-03
Stall Prevention Limit during Acceleration
L3-04
Stall Prevention Selection during
Deceleration
L3-05 Stall Prevention Selection during Run
L3-06
Stall Prevention Level during Run
L3-10
Stall Prevention Level during Deceleration
L3-11 Overvoltage Suppression Function Selection
L3-17
Target DC Bus Voltage for Overvoltage
Suppression and Stall Prevention
L3-22
Deceleration Time at Stall Prevention during
Acceleration
L3-23
Automatic Reduction Selection for Stall
Prevention during Run
L4-01
Speed Agreement Detection Level
L4-02
Speed Agreement Detection Width
L4-03
Speed Agreement Detection Level (+/-)
L4-04
Speed Agreement Detection Width (+/-)
L4-05 Frequency Reference Loss Detection Selection
L4-06 Frequency Reference at Reference Loss
L4-07 Speed Agreement Detection Selection
L5-01 Number of Auto Restart Attempts
L5-02 Auto Restart Fault Output Operation Selection
L5-04 Fault Reset Interval Time
L5-05 Fault Reset Operation Selection
L6-01 Torque Detection Selection 1
L6-02
Torque Detection Level 1
L6-03
Torque Detection Time 1
L6-04 Torque Detection Selection 2
L6-05
Torque Detection Level 2
L6-06
Torque Detection Time 2
L7-01
Forward Torque Limit
L7-02
Reverse Torque Limit
L7-03
Forward Regenerative Torque Limit
L7-04
Reverse Regenerative Torque Limit
L7-06
Torque Limit Integral Time Constant
No. Name
User
Setting
To Next Page
Loading...
