E.3 User Setting Table
YASKAWA ELECTRIC SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual 431
L7-07
Torque Limit Control Method Selection during
Accel/Decel
L8-01
Internal Dynamic Braking Resistor Protection
Selection (ERF type)
L8-02 Overheat Alarm Level
L8-03 Overheat Pre-Alarm Operation Selection
L8-05 Input Phase Loss Protection Selection
L8-07 Output Phase Loss Protection Selection
L8-09 Output Ground Fault Detection Selection
L8-10 Heatsink Cooling Fan Operation Selection
L8-11 Heatsink Cooling Fan Off-Delay Time
L8-12 Ambient Temperature Setting
L8-15 oL2 Characteristics Selection at Low Speed
L8-18 Software Current Limit Selection
L8-29 Current Unbalance Detection (LF2)
L8-35 Installation Method Selection
L8-38 Carrier Frequency Reduction Selection
L8-40 Carrier Frequency Reduction Off-Delay Time
L8-41 High Current Alarm Selection
L8-46 AVR Function Selection
L8-51 STo Level
L8-54 STo Bias Detection Selection
n1-01 Hunting Prevention Selection
n1-02 Hunting Prevention Gain Setting
n1-03 Hunting Prevention Time Constant
n1-05
Hunting Prevention Gain while in Reverse
n2-01
Speed Feedback Detection Control (AFR)
Gain
n2-02
Speed Feedback Detection Control (AFR)
Time Constant 1
n2-03
Speed Feedback Detection Control (AFR)
Time Constant 2
n3-13
Overexcitation Deceleration Gain
n3-21 Overslip Suppression Current Level
n3-23 Overexcitation Operation Selection
n8-45
Speed Feedback Detection Control Gain
n8-47 Pull-In Current Compensation Time Constant
n8-48
Pull-In Current
n8-49
d-Axis Current for High Efficiency Control
n8-50
Heavy Load Current Level
n8-51
Acceleration/Deceleration Pull-In Current
n8-54
Voltage Error Compensation Time Constant
n8-55 Load Inertia
n8-62 Output Voltage Limit
n8-63 Output Voltage Limit Gain 1
n8-65
Speed Feedback Detection Control Gain
during ov Suppression
n8-68 Output Voltage Limit Gain 2
n8-74 Id No Load Start
No. Name
User
Setting
n8-75 Id No Load End
n8-76 Id Filter Time
n8-77 Id Load Slp End
n8-78
Id Medium Value
n8-87 Output Voltage Limit Selection
n8-88 Output Voltage Limit Switch Current Level
n8-89 Output Voltage Limit Switch Hysteresis Width
n8-90 Output Voltage Limit Switch Speed
n8-91 Output Voltage Limit ld Limit
n9-10 AVR Time Constant
n9-12 On-Delay Compensation Time
n9-62
On-Delay Compensation Derating Start
Frequency
n9-63 On-Delay Compensation Disable Frequency
o1-01
Drive Mode Unit Monitor Selection
o1-02
User Monitor Selection after Power Up
o1-03 Digital Operator Display Selection
o1-10 User-Set Display Units Maximum Value
o1-11 User-Set Display Units Decimal Display
o2-01 LO/RE Key Function Selection
o2-02 STOP Key Function Selection
o2-03 User Parameter Default Value
o2-04 Drive Model Selection
o2-05
Frequency Reference Setting Method
Selection
o2-06 Digital Operator Disconnection Operation
o2-07
Motor Direction at Power Up when Using
Operator
o3-01 Copy Function Selection
o3-02 Copy Allowed Selection
o4-01 Cumulative Operation Time Setting
o4-02 Cumulative Operation Time Selection
o4-03 Cooling Fan Operation Time Setting
o4-05 Capacitor Maintenance Setting
o4-07 DC Bus Pre-charge Relay Maintenance Setting
o4-09 IGBT Maintenance Setting
o4-11 U2, U3 Initialization
o4-12 kWh Monitor Initialization
o4-13
Number of Run Commands Counter
Initialization
S1-01
Disturb Function Selection
S1-02
Disturb Function Amplitude
S1-03
Disturb Step
S1-04
Disturb Deceleration Time
S1-05
Disturb Acceleration Time
S2-01
Frequency Reference Gain
S2-02
Frequency Reference Gain Change Ramp
No. Name
User
Setting
To Next Page
Loading...
