E.3 User Setting Table
432 YASKAWA ELECTRIC SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual
S3-01 Braking Transistor Operation Selection
S3-02 Braking Transistor Operation Voltage Level
S3-03 V/f Gain Enable/Disable
S3-04
V/f Gain Change Time
S4-01 KEB Mode Selection
S4-02
KEB Start/End Voltage
S4-03
KEB Start Voltage
S4-04
KEB Start dV/dt level
S4-05
KEB Start dV/dt filter
S4-06
KEB End Voltage
S4-07
KEB End Detection Time
S4-08
KEB 1 Phase Loss Detection Level
S4-09
KEB 1 Phase Loss Sampling Time
S4-10
KEB 1 Phase Loss Detection Time
S4-11
KEB Target Voltage
S4-12
KEB Hold Time
S4-13
KEB Minimum Operation Time
S4-14
KEB Reacceleration Prohibit Frequency
S5-01
KEB1 Decel Time 1
S5-02
KEB1 Decel Time 2
S5-03
KEB1 Decel Time Switching Frequency
S5-04
KEB1 Decel Time Switching Time
S5-05
KEB1 Synchronous Acceleration Time
S5-06
S-Curve at KEB Deceleration Start
S5-07
Frequency Gain at KEB Start during Constant
Speed
S5-08
Frequency Gain at KEB Start during
Acceleration
S5-09
Frequency Gain at KEB Start during
Deceleration
S5-10 Synchronous Deceleration ov Prevention
S6-01 DC Bus Capacity
S6-02 Motor Acceleration Time
S6-03 Load/Inertia Ratio
S6-04 Main Circuit Voltage Adjustment Gain
S6-05 Accel/Decel Calculation Gain
T1-00 Motor 1 / Motor 2 Selection
T1-01 Auto-Tuning Mode Selection
No. Name
User
Setting
T1-02 Motor Rated Power
T1-03 Motor Rated Voltage
T1-04 Motor Rated Current
T1-05 Motor Rated Frequency
T1-06 Number of Motor Poles
T1-07 Motor Rated Speed
T1-11 Motor Iron Loss
U1-01 Frequency Reference
U1-02 Output Frequency
U1-03 Output Current
U1-04 Control Method
U1-05 Motor Speed
U1-06 Output Voltage Reference
U1-07 DC Bus Voltage
U1-08 Output Power
U1-09 Torque Reference
U1-10 Input Terminal Status
U1-11 Output Terminal Status
U1-12 Drive Status
U1-13 Terminal A1 Input Voltage
U1-14 Terminal A2 Input Voltage
U1-16 Output Frequency after Soft Starter
U1-18 OPE Fault Parameter
U1-19 MEMOBUS/Modbus Error Code
U1-24 Input Pulse Monitor
U1-25 Software Number (Flash)
U1-26 Software Number (ROM)
U2-01 Current Fault
U2-02 Previous Fault
U2-03 Frequency Reference at Previous Fault
U2-04 Output Frequency at Previous Fault
U2-05 Output Current at Previous Fault
U2-06 Motor Speed at Previous Fault
U2-07 Output Voltage at Previous Fault
U2-08 DC Bus Voltage at Previous Fault
U2-09 Output Power at Previous Fault
U2-10 Torque Reference at Previous Fault
U2-11 Input Terminal Status at Previous Fault
U2-12 Output Terminal Status at Previous Fault
U2-13 Drive Operation Status at Previous Fault
U2-14 Cumulative Operation Time at Previous Fault
U2-15 Soft Starter Speed Reference at Previous Fault
U2-16 Motor q-Axis Current at Previous Fault
U2-17 Motor d-Axis Current at Previous Fault
U3-01 Most Recent Fault
U3-02 2nd Most Recent Fault
U3-03 3rd Most Recent Fault
U3-04 4th Most Recent Fault
U3-05 5th Most Recent Fault
U3-06 6th Most Recent Fault
No. Name
User
Setting
To Next Page
Loading...
