YASKAWA U1000 - H4: Analog Outputs

H3 Multi-Function Analog Input Settings
H3-oo
Setting
Function LCD Display Description When Output Is 100% Page
11 Reverse torque limit Rev Torque Limit
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLVV/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLV
10 V = Motor rated torque
303
12
Regenerative torque
limit
Regen Torq Limit
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLVV/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLV
10 V = Motor rated torque
303
13
Torque reference/
Torque limit
Torque Reference
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLVV/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLV
10 V = Motor rated torque
303
14 Torque compensation Torque Comp
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLVV/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLV
10 V = Motor rated torque
303
15 General torque limit Torque Limit
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLVV/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLV
10 V = Motor rated torque
303
16
Differential PID
feedback
PID Feedback 2
All Modes
10 V = 100%
303
1F Through mode Not Used
All Modes
Select this setting when the terminal is not used or when using the terminal in the
pass-through mode.
303
30 to 32
DriveWorksEZ
analog input 1 to 3
–
All Modes
Output is determined by the function selected using DWEZ.
303
u
H4: Analog Outputs
No.
(Addr.
Hex)
Name LCD Display Description Values Page
H4-01
(041D)
Multi-Function Analog
Output Terminal FM
Monitor Selection
Term FM FuncSel
All Modes
Selects the data to be output through multi-function analog
output terminal FM.
Set the desired monitor parameter to the digits available in
Uo-oo.
For example, enter “103” for U1-03.
Default: 102
Range: 000 to
999
304
H4-02
(041E)
Multi-Function Analog
Output Terminal FM
Gain
Terminal FM Gain
All Modes
Sets the signal level at terminal FM that is equal to 100% of the
selected monitor value.
Default: 100.0%
Min.: -999.9
Max.: 999.9
304
H4-03
(041F)
Multi-Function Analog
Output Terminal FM
Bias
Terminal FM Bias
All Modes
Sets the signal level at terminal FM that is equal to 0% of the
selected monitor value.
Default: 0.0%
Min.: -999.9
Max.: 999.9
304
H4-04
(0420)
Multi-Function Analog
Output Terminal AM
Monitor Selection
Terminal AM Sel
All Modes
Selects the data to be output through multi-function analog
output terminal AM.
Set the desired monitor parameter to the digits available in
Uo-oo.
For example, enter “103” for U1-03.
Default: 103
Range: 000 to
999
304
H4-05
(0421)
Multi-Function Analog
Output Terminal AM
Gain
Terminal AM Gain
All Modes
Sets the signal level at terminal AM that is equal to 100% of
the selected monitor value.
Default: 50.0%
Min.: -999.9
Max.: 999.9
304
H4-06
(0422)
Multi-Function Analog
Output Terminal AM
Bias
Terminal AM Bias
All Modes
Sets the signal level at terminal AM that is equal to 0% of the
selected monitor value.
Default: 0.0%
Min.: -999.9
Max.: 999.9
304
B.9 H Parameters: Multi-Function Terminals
YASKAWA ELECTRIC SIEP C710636 04D U1000 Industrial MATRIX Drive Technical Manual
545
B
Parameter List