YASKAWA U1000 - Page 686

No. Name
User
Setting
F1-05 PG 1 Rotation Selection
F1-06 PG 1 Division Rate for PG Pulse Monitor
F1-08 Overspeed Detection Level
F1-09 Overspeed Detection Delay Time
F1-10 Excessive Speed Deviation Detection Level
F1-11 Excessive Speed Deviation Detection Delay Time
F1-12 PG 1 Gear Teeth 1
F1-13 PG 1 Gear Teeth 2
F1-14 PG Open-Circuit Detection Time
F1-18 dv3 Detection Selection
F1-19 dv4 Detection Selection
F1-20 PG Option Card Disconnect Detection 1
F1-21 PG 1 Signal Selection
F1-30 PG Option Card Port for Motor 2 Selection
F1-31 PG 2 Pulses Per Revolution
F1-32 PG 2 Rotation Selection
F1-33 PG 2 Gear Teeth 1
F1-34 PG 2 Gear Teeth 2
F1-35 PG 2 Division Rate for PG Pulse Monitor
F1-36 PG Option Card Disconnect Detection 2
F1-37 PG2 Signal Selection
F1-50 Encoder Selection
F1-51 PGoH Detection Level
F1-52 Communication Speed of Serial Encoder Selection
F2-01 Analog Input Option Card Operation Selection
F2-02
Analog Input Option Card Gain
F2-03
Analog Input Option Card Bias
F3-01 Digital Input Option Card Input Selection
F3-03 Digital Input Option DI-A3 Data Length Selection
F4-01 Terminal V1 Monitor Selection
F4-02
Terminal V1 Monitor Gain
F4-03 Terminal V2 Monitor Selection
F4-04
Terminal V2 Monitor Gain
F4-05
Terminal V1 Monitor Bias
F4-06
Terminal V2 Monitor Bias
F4-07 Terminal V1 Signal Level
F4-08 Terminal V2 Signal Level
F5-01 Terminal M1-M2 Output Selection
F5-02 Terminal M3-M4 Output Selection
No. Name
User
Setting
F5-03 Terminal P1-PC Output Selection
F5-04 Terminal P2-PC Output Selection
F5-05 Terminal P3-PC Output Selection
F5-06 Terminal P4-PC Output Selection
F5-07 Terminal P5-PC Output Selection
F5-08 Terminal P6-PC Output Selection
F5-09 DO-A3 Output Mode Selection
F6-01 Communications Error Operation Selection
F6-02
External Fault from Comm. Option Detection
Selection
F6-03
External Fault from Comm. Option Operation
Selection
F6-04 bUS Error Detection Time
F6-06
Torque Reference/Torque Limit Selection from
Comm. Option
F6-07
Multi-Step Speed Enable/Disable Selection when
NefRef/ComRef is Selected
F6-08 Reset Communication Parameters
F6-10 CC-Link Node Address
F6-11 CC-Link Communications Speed
F6-14 CC-Link bUS Error Auto Reset
F6-20 MECHATROLINK Station Address
F6-21 MECHATROLINK Frame Size
F6-22 MECHATROLINK Link Speed
F6-23 MECHATROLINK Monitor Selection (E)
F6-24 MECHATROLINK Monitor Selection (F)
F6-25
Operation Selection at MECHATROLINK Watchdog
Timer Error (E5)
F6-26 MECHATROLINK bUS Errors Detected
F6-30 PROFIBUS-DP Node Address
F6-31 PROFIBUS-DP Clear Mode Selection
F6-32 PROFIBUS-DP Data Format Selection
F6-35 CANopen Node ID Selection
F6-36 CANopen Communication Speed
F6-45 BACnet Node Address
F6-46 BACnet Baud Rate
F6-47 Rx to Tx Wait Time
F6-48 BACnet Device Object Identifier 0
F6-49 BACnet Device Object Identifier 1
F6-50 DeviceNet MAC Address
F6-51 DeviceNet Communication Speed
F6-52 DeviceNet PCA Setting
F6-53 DeviceNet PPA Setting
F6-54 DeviceNet Idle Mode Fault Detection
F6-55 DeviceNet Baud Rate Monitor
F6-56 DeviceNet Speed Scaling
F6-57 DeviceNet Current Scaling
E.3 User Setting Table
686
YASKAWA ELECTRIC SIEP C710636 04D U1000 Industrial MATRIX Drive Technical Manual