No. Name
User
Setting
H4-08
Multi-Function Analog Output Terminal AM Signal
Level Selection
H5-01 Drive Node Address
H5-02 Communication Speed Selection
H5-03 Communication Parity Selection
H5-04 Stopping Method After Communication Error (CE)
H5-05 Communication Fault Detection Selection
H5-06 Drive Transmit Wait Time
H5-07 RTS Control Selection
H5-09 CE Detection Time
H5-10
Unit Selection for MEMOBUS/Modbus Register
0025H
H5-11 Communications ENTER Function Selection
H5-12 Run Command Method Selection
H5-17
Operation Selection when Unable to Write into
EEPROM
H5-18 Filter Time Constant for Motor Speed Monitoring
H6-01 Pulse Train Input Terminal RP Function Selection
H6-02
Pulse Train Input Scaling
H6-03
Pulse Train Input Gain
H6-04
Pulse Train Input Bias
H6-05
Pulse Train Input Filter Time
H6-06
Pulse Train Monitor Selection
H6-07
Pulse Train Monitor Scaling
H6-08 Pulse Train Input Minimum Frequency
L1-01 Motor Overload Protection Selection
L1-02 Motor Overload Protection Time
L1-03
Motor Overheat Alarm Operation Selection (PTC
input)
L1-04
Motor Overheat Fault Operation Selection (PTC
input)
L1-05 Motor Temperature Input Filter Time (PTC input)
L1-08 oL1 Current Level
L1-09 oL1 Current Level for Motor 2
L1-13 Continuous Electrothermal Operation Selection
L2-01 Momentary Power Loss Operation Selection
L2-02 Momentary Power Loss Ride-Thru Time
L2-03 Momentary Power Loss Minimum Baseblock Time
L2-04
Momentary Power Loss Voltage Recovery Ramp
Time
L2-07 KEB Acceleration Time
L2-13 Input Power Frequency Fault Detection Gain
No. Name
User
Setting
L2-21 Low Input Voltage Detection Level
L2-27 Input Power Frequency Fault Detection Width
L3-01 Stall Prevention Selection during Acceleration
L3-02 Stall Prevention Level during Acceleration
L3-03 Stall Prevention Limit during Acceleration
L3-04 Stall Prevention Selection during Deceleration
L3-05 Stall Prevention Selection during Run
L3-06 Stall Prevention Level during Run
L3-14 Stall Prevention Level during Deceleration
L3-22
Deceleration Time at Stall Prevention during
Acceleration
L3-23
Automatic Reduction Selection for Stall Prevention
during Run
L3-27 Stall Prevention Detection Time
L3-36
Vibration Suppression Gain during Acceleration (with
Current Limit)
L3-39
Current-limited Integral Time Constant during
Acceleration
L3-40
Current-limited Maximum S-curve Selection during
Acceleration
L3-41
Vibration Suppression Gain during Deceleration (with
Current Limit)
L3-44
Current-limited Integral Time Constant during
Deceleration
L3-45
Current-limited Maximum S-curve Selection during
Deceleration
L4-01 Speed Agree Detection Level
L4-02 Speed Agree Detection Width
L4-03 Speed Agree Detection Level (+/-)
L4-04 Speed Agree Detection Width (+/-)
L4-05 Frequency Reference Loss Detection Selection
L4-06 Frequency Reference at Reference Loss
L4-07 Speed Agree Detection Selection
L5-01 Number of Auto Restart Attempts
L5-02 Auto Restart Fault Output Operation Selection
L5-04 Fault Reset Interval Time
L5-05 Fault Reset Operation Selection
L6-01 Torque Detection Selection 1
L6-02 Torque Detection Level 1
L6-03 Torque Detection Time 1
L6-04 Torque Detection Selection 2
L6-05 Torque Detection Level 2
L6-06 Torque Detection Time 2
L6-08 Mechanical Weakening Detection Operation
L6-09 Mechanical Weakening Detection Speed Level
L6-10 Mechanical Weakening Detection Time
L6-11 Mechanical Weakening Detection Start Time
L7-01 Forward Torque Limit
E.3 User Setting Table
688
YASKAWA ELECTRIC SIEP C710636 04D U1000 Industrial MATRIX Drive Technical Manual
To Next Page
Loading...
