To Next Page

To Previous Page

Electrical installation 25

Electrical installation

What this chapter contains

This chapter contains:

• general cabling instructions

• grounding instructions

• instructions on setting the IP address

• instructions on connecting the NETA-21 to the drive and to the Ethernet network.

WARNING! Only qualified electricians are allowed to carry out the work described

in this chapter. Follow the instructions in section Safety in installation. Ignoring the

safety instructions can cause physical injury or death.

General cabling instructions

• Arrange the cables as far away from the power cables as possible.

• Avoid parallel runs with the power cables.

See chapter Technical data for information on cable types.

Default Chapter5
- Table of Contents5
1 Safety11
- What this Chapter Contains11
- Use of Warnings11
- Safety in Installation12
2 Introduction to the Manual13
- What this Chapter Contains13
- Applicability13
- Compatibility13
- Target Audience14
- Purpose of the Manual14
- Before You Start15
- Contents15
- Terms and Abbreviations Used in this Manual16
  - Terms16
  - Abbreviations17
3 Overview19
- What this Chapter Contains19
- NETA-21 Remote Monitoring Tool19
- NETA-21-Specific Features20
  - Layout of the NETA-21 and the NEXA-2121
- Hardware and Software Requirements of the PC22
4 Mechanical Installation23
- What this Chapter Contains23
- Unpacking and Examining the Delivery23
- Installing NEXA-21 to NETA-2124
- Installing the NETA-2124
5 Electrical Installation25
- What this Chapter Contains25
- General Cabling Instructions25
- Grounding26
- Power Connections26
- Communication Connections26
6 Start-Up33
- Contents of this Chapter33
- First Access to the User Interface33
  - Connecting a Local PC to the NETA-21 in the DHCP Server Mode34
  - Logging on to the NETA-2134
- Basic Settings36
- Initializing the Communication between the NETA-21 and Drives Online41
  - Initializing the Communication between the NETA-21 and ACS800 Drives (or Other Drives with the RDCU Control Unit)41
7 Program Features43
- What this Chapter Contains43
- Ftp/Ftps43
- Http44
- Https44
  - HTTPS Certificate44
- Modbus/Tcp Gateway45
  - Ethernet PC Tool Gateway46
- TCP and UDP Service Ports47
- Cybersecurity Disclaimer49
8 Front Page51
- What this Chapter Contains51
- Parts and Components of the Portal51
9 Users57
- What this Chapter Contains57
- My Details57
- User Management58
  - Users Tab58
    - User Properties60
- User Roles61
- User Interface66
10 Devices69
- What this Chapter Contains69
- Devices Tab69
  - Device71
    - Device Control Buttons72
  - Parameter Browser73
- Device Data Logger79
- Device Interface Settings85
11 Networks101
- What this Chapter Contains101
- Network Interfaces View101
- Network Services104
- Dhcp107
- Http/Https107
- Starting up the SMTP Configuration108
- Ftp/Ftps109
- Dynamic DNS110
  - Using the Dynamic DNS Service110
- Dial-Up Function111
  - Using a Mobile Broadband Connection112
12 Events115
- What this Chapter Contains115
- Universal Event List115
  - Contents of the Non-Universal Event List117
- Filtering Settings by Columns117
- Filtering Settings through the Event Filter Panel119
13 Reporting121
- What this Chapter Contains121
- Introduction to Reporting121
- Configuring the NETA-21 for Reporting122
- Creating an Email Report124
  - Format of the Email Report125
- Creating an SD Card Report126
  - Format of an SD Card Report127
    - CSV-Formatted Reports127
    - DB-Formatted Reports128
- Creating an FTP Report129
  - Format of an FTP Report131
- Creating SMS Report131
- Setting the Report Trigger133
- Setting the Reported Data135
- Changing the Reporting Name137
- Changing the Default Naming of Signals138
- Parameter Logging Interval Templates139
  - Changing the Continuous Monitor Interval141
- Using Scripting for Email Reports (Custom Report)142
- Using Scripting for SMS Reports (Custom Report)143
- Description of the Tabs under Reports144
14 Tools151
- What this Chapter Contains151
- Tool Firmware151
- Factory Tools153
  - IP Address after a Factory Reset154
- Packages154
- Using ABB IP Configuration Tool155
15 Backup and Restore157
- What this Chapter Contains157
- Backing up the NETA-21157
- Restoring the NETA-21159
16 Security161
- What this Chapter Contains161
- Applicability161
- Advantages161
- Features161
- Protocol Level Implementation for RADIUS162
- Enabling RADIUS Authentication in NETA-21 Web UI163
17 Memory Card173
- What this Chapter Contains173
- Using the Memory Card173
- Memory Card Status Tab173
- File Browser Tab174
- Autoinst Tab174
- Backup Tab175
- Report Tab175
- Restore Tab175
18 Frequently Asked Questions177
- What this Chapter Contains177
- How to Update the NETA-21 Firmware177
- How to Reset the Factory Settings / What if I Forget My Password182
- How to Replace the SD Memory Card Safely182
- How to Configure the Logging of Drive Data to the SD Card182
- How Much Logged Data Fits into an SD/SDHC Card183
- How to Interpret the Logged Data from the SD Card183
- How to Create an FTP Account183
- How to Re-Enable Reports if Time & Date Have Been Shifted Backwards183
19 Diagnostics and Troubleshooting185
- What this Chapter Contains185
- LED Indications185
  - LED Indications of the NETA-21186
  - LED Indications of the NEXA-21188
- Troubleshooting188
20 Technical Data191
- What this Chapter Contains191
- Hardware192
Further Information195
- Product and Service Inquiries195
- Product Training195
- Providing Feedback on ABB Drives Manuals195
- Document Library on the Internet195

Brand	ABB
Model	NETA-21
Category	Measuring Instruments
Language	English

ABB NETA-21 User Manual

Table of Contents

Other manuals for ABB NETA-21

Questions and Answers:

ABB NETA-21 Specifications

Related product manuals