Alcatel-Lucent 9558HC - Page 21

List of Figures
MPR-e 21
Figure 257 Coupler Polarization Change (6-7-8 GHz) ...................................................................................337
Figure 258 Waterproofness tape....................................................................................................................337
Figure 259 Vertical polarization......................................................................................................................338
Figure 260 Top disk, showing V indication.....................................................................................................338
Figure 261 Bottom disk ..................................................................................................................................338
Figure 262 Bottom disk, after rotation ............................................................................................................339
Figure 263 Top disk, showing H indication ....................................................................................................339
Figure 264 Horizontal polarization .................................................................................................................339
Figure 265 Installing the RF coupler to the radio support (6-7-8 GHz) ..........................................................340
Figure 266 Putting silicone grease on O-ring before MPT-HC insertion (6-7-8 GHz) ....................................341
Figure 267 Installing the MPT-HC 1+1 on the RF coupler (6-7-8 GHz) .........................................................341
Figure 268 "Pole Mounting for Remote ODU" installation..............................................................................342
Figure 269 Putting silicone grease on O-ring before RF coupler insertion ....................................................343
Figure 270 11-38 GHz RF coupler installation (with pole mounting P/N 3DB10137AAXX) ...........................343
Figure 271 Putting silicone grease on RF coupler’s O-ring before MPT-HC insertion (11-38 GHz) ..............344
Figure 272 Installation of MPT-HC 1+1 (11-38 GHz) .....................................................................................345
Figure 273 "Pole Mounting for Remote ODU" installation..............................................................................346
Figure 274 Putting silicone grease on O-ring before RF coupler insertion ....................................................347
Figure 275 6-7-8 GHz RF coupler installation (with pole mounting P/N 3DB10137AAXX)............................347
Figure 276 Putting silicone grease on O-ring before MPT-HC insertion (6-7-8 GHz) ....................................348
Figure 277 Installing the MPT-HC 1+1 on the RF coupler (7-8 GHz) ............................................................348
Figure 278 MPT-HC 1+1 installed on the RF coupler (6-7-8 GHz) ................................................................349
Figure 279 On SBX-AMPT and SCX-AMPT antennas the radio interface is not present. .............................350
Figure 280 Feeder plate and OMT antenna interface ....................................................................................351
Figure 281 Insert the assembly in the antenna ..............................................................................................351
Figure 282 Apply silicone grease when necessary before inserting the OMT ...............................................352
Figure 283 Fix the fine tuning plate to the OMT body ....................................................................................352
Figure 284 Apply silicone grease if necessary...............................................................................................353
Figure 285 Fasten the MPT-HC V2/MPT-XP to the OMT ..............................................................................354
Figure 286 MPT-HC V2/MPT-XP fastened to the OMT .................................................................................354
Figure 287 Fine tuning ...................................................................................................................................355
Figure 288 Assemble the feeder and the feeder plate on the OMT interface ................................................356
Figure 289 Insert the assembly in the antenna ..............................................................................................357
Figure 290 Apply silicone grease ...................................................................................................................357
Figure 291 Place and fix the OMT to the interface.........................................................................................358
Figure 292 Engraved arrow toward pipe ........................................................................................................359
Figure 293 Apply silicone grease ...................................................................................................................360
Figure 294 Locking hooks and fastening brackets.........................................................................................361
Figure 295 Fine tuning ...................................................................................................................................362
Figure 296 Kit plug R2CT...............................................................................................................................363
Figure 297 Kit plug R2CT items.....................................................................................................................363
Figure 298 Remove the protection cap ..........................................................................................................364
Figure 299 Unscrew the nut spiral .................................................................................................................364
Figure 300 Pass cable through the mini kit plug ............................................................................................364
Figure 301 Crimp the RJ-45 plug ...................................................................................................................365
Figure 302 EIA/TIA standard..........................................................................................................................365
Figure 303 Insert the RJ-45 plug in the unlocking clip ...................................................................................365
Figure 304 Insert the unlocking clip ...............................................................................................................366
Figure 305 Pull the coupling nut ....................................................................................................................366