Allen-Bradley 20F Installation Instructions

Rockwell Automation Publication 750-IN001P-EN-P - April 2017 189
Power Wiring Chapter 4
Table 25 - 690 Volt AC and 932 Volt DC Input Protection Devices – Wall Mount Frames 6…7
Applied Rating
(1)
Frame
Cont. Output Amps
Drive Sized For Normal Duty Drive Sized For Heavy Duty Continuous
AC Input
AC Input Protection Devices Input
Quantities
DC Input Protection
Catalog Number
Output Overload Amps Catalog
Number
Output Overload Amps Dual Element
Time Delay Fuse
Non-Time Delay Fuse
Circuit Breaker Max Size
(6)
Motor Circuit Protector
(7)
Continuous DC Input
Non-Time Delay Fuse
(x = F or G) 1 min 3 sec (x = F or G) 1 min 3 sec Amps Min
(2)
Max
(5)
Min
(2)
Max
(5)
Amps
690 Volt AC Input 932 Volt DC Input 5.5 kW 6
9 20x…F011 13.5 18.0 8.4 11 19 11 25 30 15 9.9 HSJ15
7.5 kW 6 12 20x…F011 13.2 18.0 20x…F015 18.0 22.5 11.2 14 25 14 35 40 15 13.2 HSJ20 11 kW 6
15 20x…F015 16.5 22.5 20x…F020 22.5 30.0 14.1 18 32 18 40 50 20 16.5 HSJ25
15 kW 6 20 20x…F020 22.0 30.0 20x…F023 30.0 36.0 18.7 23 42 23 55 60 25 21.9 HSJ35 18.5 kW 6
23 20x…F023 25.3 34.5 20x…F030 34.5 45.0 21.6 27
(3)
, 25
(4)
48
(3)
, 50
(4)
27
(3)
, 25
(4)
65 70 30 25.2 HSJ40
22 kW 6 30 20x…F030 33.0 45.0 20x…F034 45.0 54.0 28.1 35 65 35 85 90 40 32.9 HSJ50 30 kW 6
34 20x…F034 37.4 51.0 20x…F046 51.0 69.0 31.9 40 70 40 95 100 40 37.3 HSJ60
37 kW 6 46 20x…F046 50.6 69.0 20x…F050 69.0 82.8 43.1 55 95 55 130 130 55 50.5 HSJ80 45 kW 6
50 20x…F050 55.0 75.0 20x…F061 75.0 91.5 46.9 60 105 60 140 150 60 54.8 HSJ90
55 kW 6 61 20x…F061 67.1 91.5 20x…F082 91.5 123.0 57.2 70 130 70 170 180 75 66.9 HSJ100 75 kW 6
82 20x…F082 90.2 123.0 20x…F098 123.0 147.6 76.8 95 175 95 230 240 100 89.9 HSJ150
90 kW 6 98 20x…F098 107.8 147.0 20x…F119 147.0 178.5 91.8 115 205 115 275 280 115 107.5 HSJ175 110 kW 6
119 20x…F119 130.9 178.5 20x…F142 178.5 214.2 111.5 140 250 140 335 340 140 130.5 HSJ200
132 kW 6 142 20x…F142 156.2 213.0
133.1 165 300 165 400 400 170 155.7 HSJ250
7
142 20x…F171 213.0 256.5 133.1 165 300 165 400 400 170 155.7 HSJ250
160 kW 7 171 20x…F171 188.1 256.5 20x…F212 256.5 318.0 160.2 200 360 200 480 490 205 187.5 HSJ300 200 kW 7
212 20x…F212 233.2 318.0 20x…F263 318.0 394.5 198.7 250 445 250 595 600 250 232.5 HSJ350
250 kW 7 263 20x…F263 289.3 394.5
246.5 310 555 310 740 740 310 288.4 HSJ500
(1) “Applied Rating” refers to the motor that will be connected to the drive. For example, a “F061” drive can be used in Normal Duty mode on a55 kW motor, in Heavy-duty mode on a 45 kW motor. The drive can be programmed for each mode. Wiring and fuses can be sized
based on the programmed mode. For any given drive catalog number, Normal Duty mode provides higher continuous current but smaller overload current when compared to Heavy-duty mode. See parameter 306 [Duty Rating]. See Specifications for an explanation of Duty Ratings.
(2) Minimum protection device size is the lowest rated device that supplies maximum protection without nuisance tripping. (3) Normal duty. (4) Heavy duty. (5) Maximum protection device size is the highest rated device that supplies drive protection. For US NEC, minimum size is 125% of motor FLA. Ratings that are shown are maximum. (6) Circuit Breaker – inverse time breaker. For US NEC, minimum size is 125% of motor FLA. Ratings that are shown are maximum. (7) Recommended Motor circuit protector – Instantaneous trip circuit breaker. Set the trip setting to the input current of the drive and size for the continuous current of the system.

Allen-Bradley 20F Specifications

General

Brand	Allen-Bradley
Model	20F
Category	Controller
Language	English