Configuration Mode (ConF)
Assignment of the inputs/outputs
Input/
output
[Start/Stop] [M . handling] [Gen. Use] [Hoisting] [PID regul.] [Netw ork C.]
[AI1]
[Ref.1 channe l]
[Ref.1 channe l] [Re f.1 channel] [Ref.1 channe l] [Ref.1 channe l]
(PID
reference)
[Ref.2 channe l]
(
[Ref.1 channe l
]
= integrated
Modbus) (1)
[AI2]
[No] [Sum ming ref. 2] [Sum ming ref. 2] [No] [PID feedback] [No]
[AI3]
[No] [No] [No] [No] [No] [No]
[AO1]
[No] [No] [No] [No] [No] [No]
[R1]
[No drive flt] [No drive flt] [No drive flt] [No drive flt] [No drive flt] [No drive flt]
[R2]
[No] [No] [No] [Brk control] [No] [No]
[LI1] (2-wire)
[Forw ard] [Forw ard] [Forw ard] [Forw ard] [Forw ard] [Forw ard]
[LI2] (2-wire)
[Reve rse] [Reverse] [Re ve rse] [Re ve rse] [Reve rse] [Re verse]
[LI3] (2-wire)
[No] [2 preset speeds] [Jog] [Fault reset] [PID integral reset] [Re f. 2
sw itching]
[LI4] (2-wire)
[No] [4 preset speeds] [Fault re s et] [Exte rnal fault] [2 pre s et PID
re f.]
[Fault reset]
[LI5] (2-wire)
[No] [8 preset speeds] [Torque limitation]
[No] [4 pre s et PID
re f.]
[No]
[LI6] (2-wire)
[No] [Fault reset] [No] [No] [No] [No]
[LI1] (3-wire)
[Drive running]
[Drive running] [Drive running] [Drive running] [Drive running] [Drive running]
[LI2] (3-wire)
[Forw ard] [Forw ard] [Forw ard] [Forw ard] [Forw ard] [Forw ard]
[LI3] (3-wire)
[Reve rse] [Reverse] [Re ve rse] [Re ve rse] [Reve rse] [Re verse]
[LI4] (3-wire)
[No] [2 preset speeds] [Jog] [Fault reset] [PID integral
re s et]
[Ref. 2
sw itching]
[LI5] (3-wire)
[No] [4 preset speeds] [Fault re s et] [Exte rnal fault] [2 pre s et PID
re f.]
[Fault reset]
[LI6] (3-wire)
[No] [8 preset speeds] [Torque limitation]
[No] [4 pre s et PID
re f.]
[No]
[LO1]
[No] [No] [No] [No] [No] [No]
Graphic display terminal keys
F1 key
[No] [No] [No] [No] [No]
Control via
graphic display
terminal
F2, F3, F4
keys
[No] [No] [No] [No] [No] [No]
In 3-w ire control, the assignment of inputs LI1 to LI6 shifts.
(1) To start w ith, integrated Modbus
[M odbus Address ]
(Add) must first be configured, page 276.
Note:
Thes e as signments are reinitialized every tim e the m acro configuration changes.
To Next Page
Loading...
