Cisco ASR 9000 Series Routing Configuration Guide

RP/0/RSP0/CPU0:router(config-bgp)# address-family vpnv4 unicast
RP/0/RSP0/CPU0:router(config-bgp-af)#
L2VPN Address Family Configuration Mode
The following example shows how to enter L2VPN address family configuration mode:
RP/0/RSP0/CPU0:router(config)# router bgp 100
RP/0/RSP0/CPU0:router(config-bgp)# address-family l2vpn vpls-vpws
RP/0/RSP0/CPU0:router(config-bgp-af)#
Neighbor Submode
Cisco IOS XR BGP uses a neighbor submode to make it possible to enter configurations without having to
prefix every configuration with the neighbor keyword and the neighbor address:
•
Cisco IOS XR software has a submode available for neighbors in which it is not necessary for every
command to have a “neighbor x.x.x.x” prefix:
In Cisco IOS XR software, the configuration is as follows:
RP/0/RSP0/CPU0:router(config-bgp)# neighbor 192.23.1.2
RP/0/RSP0/CPU0:router(config-bgp-nbr)# remote-as 2002
RP/0/RSP0/CPU0:router(config-bgp-nbr)# address-family ipv4 unicast
•
An address family configuration submode inside the neighbor configuration submode is available for
entering address family-specific neighbor configurations. In Cisco IOS XR software, the configuration
is as follows:
RP/0/RSP0/CPU0:router(config-bgp)# neighbor 2002::2
RP/0/RSP0/CPU0:router(config-bgp-nbr)# remote-as 2023
RP/0/RSP0/CPU0:router(config-bgp-nbr)# address-family ipv6 unicast
RP/0/RSP0/CPU0:router(config-bgp-nbr-af)# next-hop-self
RP/0/RSP0/CPU0:router(config-bgp-nbr-af)# route-policy one in
•
You must enter neighbor-specific IPv4, IPv6, VPNv4, or VPNv6 commands in neighbor address-family
configuration submode. In Cisco IOS XR software, the configuration is as follows:
RP/0/RSP0/CPU0:router(config)# router bgp 109
RP/0/RSP0/CPU0:router(config-bgp)# neighbor 192.168.40.24
RP/0/RSP0/CPU0:router(config-bgp-nbr)# remote-as 1
RP/0/RSP0/CPU0:router(config-bgp-nbr)# address-family ipv4 unicast
RP/0/RSP0/CPU0:router(config-bgp-nbr-af)# maximum-prefix 1000
•
You must enter neighbor-specific IPv4 and IPv6 commands in VRF neighbor address-family configuration
submode. In Cisco IOS XR software, the configuration is as follows:
RP/0/RSP0/CPU0:router(config)# router bgp 110
RP/0/RSP0/CPU0:router(config-bgp)# vrf vrf_A
RP/0/RSP0/CPU0:router(config-bgp-vrf)# neighbor 11.0.1.2
RP/0/RSP0/CPU0:router(config-bgp-vrf-nbr)# address-family ipv4 unicast
RP/0/RSP0/CPU0:router(config-bgp-vrf-nbr-af)# route-policy pass all in
Cisco ASR 9000 Series Aggregation Services Router Routing Configuration Guide, Release 5.3.x
19
Implementing BGP
BGP Configuration

Cisco ASR 9000 Series Specifications

General

Brand	Cisco
Model	ASR 9000 Series
Category	Network Router
Language	English