Troubleshooting
DeLaval voluntary milking system VMS
94897201.pdf2007-12-18
Communication and data transmission
between the milking station and
peripheral units (VMS I/O-man) - major
code 6
M m Alarm text Type Meaning ActionM m Alarm text Type Meaning Action
6 1 AlcomIO
board reset
node ... bus
...
Deviation One of the ALCOM I/O boards has
been reset.
The system will repond by
activating all ALCOM I/O boards.
If problem occurs frequently, contact
service engineer.
6 1 AlcomIO
board reset
node ... bus
...
Deviation One of the ALCOM I/O boards has
been reset.
The system will repond by
activating all ALCOM I/O boards.
If problem occurs frequently, contact
service engineer.
6 100 Shortcircuit
on alcomio
node ...
Stop alarm One of the ALCOM I/O boards has
an output that takes too much
current, which could be a caused
by a short-circuit. The board will
automatically protect itself by
setting all I/O to input until it has
been reset.
Restart the milking station.
If the problem persists, contact service
engineer.
6 100 Shortcircuit
on alcomio
node ...
Stop alarm One of the ALCOM I/O boards has
an output that takes too much
current, which could be a caused
by a short-circuit. The board will
automatically protect itself by
setting all I/O to input until it has
been reset.
Restart the milking station.
If the problem persists, contact service
engineer.
6 101 Alcom write
error ... node
... sub
Deviation An transmission error has occurred
on the ALCOM bus.
If problem occurs frequently, contact
service engineer.
6 101 Alcom write
error ... node
... sub
Deviation An transmission error has occurred
on the ALCOM bus.
If problem occurs frequently, contact
service engineer.
6 102 Alcom
message
invalid node
...
Deviation The received ALCOM message
was incorrect.
If problem occurs frequently, contact
service engineer.
6 102 Alcom
message
invalid node
...
Deviation The received ALCOM message
was incorrect.
If problem occurs frequently, contact
service engineer.
6 103 Bad format
on alcom
message
Deviation ALCOM message is in an invalid
format.
If problem occurs frequently, contact
service engineer.
6 103 Bad format
on alcom
message
Deviation ALCOM message is in an invalid
format.
If problem occurs frequently, contact
service engineer.
6 104 Vmsio
interupt (...)
Stop alarm The VMS I/O board has generated
an unexpected interrupt.
If problem occurs frequently, contact
service engineer.
6 104 Vmsio
interupt (...)
Stop alarm The VMS I/O board has generated
an unexpected interrupt.
If problem occurs frequently, contact
service engineer.
6 105 Invalid
alcom bus
number ...
Stop alarm Software error. If problem occurs frequently, contact
service engineer.
6 105 Invalid
alcom bus
number ...
Stop alarm Software error. If problem occurs frequently, contact
service engineer.
6 106 Lost token
on alcomio
node
Deviation Communication error on the
ALCOM bus.
If problem occurs frequently, contact
service engineer.
6 106 Lost token
on alcomio
node
Deviation Communication error on the
ALCOM bus.
If problem occurs frequently, contact
service engineer.
6 107 Vmslo board
generated
reset!!
Deviation/St-
op alarm
Reset on VMS I/O board, either
because someone pressed the
reset button or because of
electrical disturbances.
Note: a single reset will generate a
Deviation only.
Restart the milking station.
If the problem occurs frequently, contact
service engineer.
6 107 Vmslo board
generated
reset!!
Deviation/St-
op alarm
Reset on VMS I/O board, either
because someone pressed the
reset button or because of
electrical disturbances.
Note: a single reset will generate a
Deviation only.
Restart the milking station.
If the problem occurs frequently, contact
service engineer.
6 108 VmsIO pic
has wrong
version !!
Stop alarm Microprocessor on VMS I/O board
has wrong program version.
Contact service engineer.
Service engineer only: Change
microprocessor or reprogram it.
6 108 VmsIO pic
has wrong
version !!
Stop alarm Microprocessor on VMS I/O board
has wrong program version.
Contact service engineer.
Service engineer only: Change
microprocessor or reprogram it.
6 109 VmsIo board
wrong
version is ...
!!
Stop alarm Wrong version of FPGA on VMS
I/O board.
Contact service engineer.
Service engineer only: This can only
happen if the VMS I/O board has been
changed to the wrong type.
Replace IC103 from the removed board and
place it on the installed board.
6 109 VmsIo board
wrong
version is ...
!!
Stop alarm Wrong version of FPGA on VMS
I/O board.
Contact service engineer.
Service engineer only: This can only
happen if the VMS I/O board has been
changed to the wrong type.
Replace IC103 from the removed board and
place it on the installed board.
6 110 Unexpected
sensor
status node
... 0f sub ... 0f
User
notification
Some sensors in the Milk sampler
indicate a problem in moving the
runner to the correct sample
position.
Check the Milk sampler and make sure that
the runner can move smoothly.
6 110 Unexpected
sensor
status node
... 0f sub ... 0f
User
notification
Some sensors in the Milk sampler
indicate a problem in moving the
runner to the correct sample
position.
Check the Milk sampler and make sure that
the runner can move smoothly.
6 111 I/O blocked User
notification
Some actuator has been blocked
by some signal.
This is only for information.6 111 I/O blocked User
notification
Some actuator has been blocked
by some signal.
This is only for information.
186(198)
To Next Page
Loading...
