Draytek Vigor2860 - Page 741

Vigor2860 Series User’s Guide
72
7
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
a
a
d
d
s
s
l
l
a
a
n
n
n
n
e
e
x
x
This command can display the annex interface of this router.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> adsl annex
% hardware is annex B.
% modem code is annex B; built at 01/15,07:34.
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
a
a
d
d
s
s
l
l
a
a
u
u
t
t
o
o
m
m
o
o
d
d
e
e
This command is used to add or remove ADSL modes (such as ANNEXL, ANNEXM and ANNEXJ)
supported by Multimode.
S
S
y
y
n
n
t
t
a
a
x
x
adsl automode [add|remove|set|default|show] [adsl_mode]
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
P
P
a
a
r
r
a
a
m
m
e
e
t
t
e
e
r
r
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
add It means to add ADSL mode.
remove It means to remove ADSL mode.
set It means to use default settings plus the new added ADSL mode.
default It means to use default settings.
show It means to display current setting.
adsl_mode There are three modes to be choose, ANNEXL, ANNEXM (annexA:
ADSL over POTS) and ANNEXJ (annexB: ADSL over ISDN).
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> adsl automode set ANNEXJ
Automode supported : T1.413, G.DMT, ADSL2, ADSL2+, ANNEXJ,
> adsl automode default
Automode supported : T1.413, G.DMT, ADSL2, ADSL2+,
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
a
a
d
d
s
s
l
l
s
s
h
h
o
o
w
w
b
b
i
i
n
n
s
s
This command can display the allocation for each Bin (Tone) SNR, Gain, and Bits.
S
S
y
y
n
n
t
t
a
a
x
x
adsl showbins [startbin endbin | up]
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
startbin The number is between 0 ~ 4092.
endbin The number is between 4 ~ 4095.
up Show upstream information.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> adsl showbins 2 30
DOWNSTREAM :