Extron electronics SMP 300 Series User Manual

SMP 300 Series • Remote Communication and Control 111
X4$
=
Audio bit rate — 80, 96, 128, 192, 256, 320
X4%
=
GOP length — 1 to 300
X4^
=
Record resolution
1 = 480p
2 = 720p
3 = 1080p
4 = WCIF (512x288)
5 = XGA (1024x768)
6 = SXGA (1280x1024)
99 = Custom
X4&
=
Record frame rate
1 = 30 5 = 12.5
2 = 25 6 = 12
3 = 24 7 = 10
4 = 15 8 = 5
X4*
=
Output refresh rate
1 = 60 Hz (default)
2 = 50 Hz
X4(
=
Aspect ratio
01 = Fill (the input automatically fills the entire output
raster; default)
02 = Follow (the input is displayed in its native
aspect ratio)
03 = Fit (the input is zoomed in to fill the entire
output raster while maintaining its aspect ratio)
X5!
=
Executive mode:
0 = Off (default)
1 = Complete lockout (no front panel control)
2 = Menu lockout (menu only)
3 = Allow recording controls only
X6$
=
HDMI output
0 = Channel A full screen
1 = Channel B full screen
2 = Confidence layout
X6&
=
EDID user location (1, 2, and 3)
X6*
=
EDID resolution (see EDID table on page42)
X6(
=
Port timeout in tens of seconds 1 to 65000 (zero
padded. Default: 00030 = 300 seconds)
X10)
=
Default name — Combination of model name and
last three pairs of MAC address
(for example: SMP-351-07-8C-EC)
X50)
=
Stream selection
1 = Archive Channel A
2 = Archive Channel B (Available for Dual Mode only)
3 = Confidence
4 = Virtual input 1 re‑stream
5 = Virtual input 2 re‑stream
X50!
=
Input number 1 to 5
1 or 2 digit command, Two‑digit response
X50@
=
Output channel
1 = A (input 1 and 2)
2 = B (input 3, 4, and 5)
X50#
=
Encoding mode
0 = Composite mode
1 = Dual channel mode
X50$
=
Input video format
1 = YUVp / HDTV (default)
2 = YUVi
3 = Composite
4 = 3G‑SDI
5 = HD‑SDI
6 = SDI
7 = Auto‑SDI (Input 5 default)
X50%
=
Stream name — Up to 16 alphanumeric characters,
a hyphen (‑), or underscore (_)
X50^
=
Audio selection
40000 = Analog Input A (Left)
40001 = Analog Input A (Right)
40002 = Digital input A (Left)
40003 = Digital input A (Right)
40004 = Analog Input B (Left)
40005 = Analog Input B (Right)
40006 = Digital input B (Left)
40007 = Digital input B (Right)
60000 = Output (Left, for audio mute control only)
60001 = Output (Right, for audio mute control only)
X50&
=
Audio level in 0.1 dB steps —
-180 to 240 = -18.0 to +24.0 dB
X51)
=
Overscan
0 = 0 % (default = HDMI inputs)
1 = 2.5 % (default: YUVp input)
2 = 5.0 % (default: YUVi and composite inputs)
X51!
=
HDCP status
0 = No sink/source detected
1 = HDCP detected,
2 = Sink/source detected but no HDCP
X51@
=
HDCP notification
0 = Off (mute output to black)
1 = On (green HDCP notification‑screen, default)
X51$
=
Input name, up to 16 characters —
Default = Input X where X is the input number
X52(
=
Json string of recording profile parameters
(for example:{“id”:1,“name”:“RECORD
PROFILE01, “contributor”:“Contributor1,
“coverage”:Coverage1”...}
X53)
=
User/Encoder/Layout Preset number —
1 to 32 (two‑digit response — 0 padding)
X53!
=
Preset name — Up to 16 characters
X53@
=
Input preset number — 1 to 128
X53#
=
Streaming preset — 1 to 16
(two‑digit response — 0 padding)

Extron electronics SMP 300 Series Specifications

General

Brand	Extron electronics
Model	SMP 300 Series
Category	Computer Hardware
Language	English