Programming manual
CNC 8070
CNC VARIABLES
Related to the machine configuration
14.
(SOFT V02.0X)
399
These variables are read/write (R/W) synchronous and are evaluated during execution. They
correspond to linear and rotary axes and to the spindle.
The PLC reading of TORQUE comes in tenths (x10) Ver "Access to numeric values from the PLC"
en la página 358.
These variables are read/write (R/W) synchronous and are evaluated during block execution.
They are valid for linear and rotary axes and for the spindle.
In order for the feed-forward and the AC-forward defined this way to be taken into account, they must
be active by machine parameter; i.e. by means of machine parameter FFWTYPE if it is an analog drive
or a simulated drive or parameter OPMODEP if it is a Sercos drive.
The values defined by these variables prevail over the ones defined by machine parameters or by
program. Setting the variables with a negative value cancels their effect ("0" is a valid value). These
variables are initialized neither by a reset nor when validating the parameters.
The PLC will read them in the following units. Ver "Access to numeric values from the PLC" en la
página 358.
The PLC reading of PLCACFGAIN comes in tenths (x10)
The PLC reading of PLCFFGAIN comes in hundredths (x100)
These variables are read-only (R) synchronous and are evaluated in the execution.
RELATED TO THE TANDEM AXIS PRG PLC INT
(V.)[n].A.TPIIN.Xn
Input of the PI of the master axis of the tandem (in rpm) R R R
(V.)[n].A.TPIOUT.Xn
Output of the PI of the master axis of the tandem (in rpm) R R R
(V.)[n].A.TFILTOUT.Xn
Output of the pre-load filter R R R
(V.)[n].A.PRELOAD.Xn
Preload R/W R/W R/W
(V.)[n].A.FTEO.Xn
Velocity command for Sercos R R R
(V.)[n].A.TORQUE.Xn
Current torque in Sercos R R R
VARIABLES TO BE SET VIA PLC
PRG PLC INT
(V.)[n].A.PLCFFGAIN.Xn
% of feed-forward programmed from the PLC R R/W R
(V.)[n].A.PLCACFGAIN.Xn
% of AC-forward programmed from the PLC R R/W R
(V.)[n].A.PLCPROGAIN.Xn
Proportional gain programmed from the PLC R R/W R
To set the Z axis variable to ·99.1· from the PLC:
()=MOV 991 R1
()=CNCWR(R1,A.PLCACFGAIN.Z,M1000)
To set the X axis variable to ·99.12· from the PLC:
()=MOV 9912 R1
()=CNCWR(R1,A.PLCFFGAIN.X,M1000)
VARIABLES FOR ADJUSTING THE POSITION
PRG PLC INT
(V.)[n].A.POSINC.Xn
Real position increment of the current sampling period R R R
(V.)[n].A.TPOSINC.Xn
Theoretical position increment of the current sampling period R R R
(V.)[n].A.PREVPOSINC.Xn
Real position increment of the previous sampling period R R R
FINE ADJUSTMENT VARIABLES PRG PLC INT
(V.)[n].A.FEED.Xn
Real instantaneous feedrate value R R R
(V.)[n].A.TFEED.Xn
Theoretical instantaneous feedrate value R R R
(V.)[n].A.ACCEL.Xn
Real instantaneous acceleration value R R R
(V.)[n].A.TACCEL.Xn
Theoretical instantaneous acceleration value R R R
(V.)[n].A.JERK.Xn
Real instantaneous jerk value R R R
(V.)[n].A.TJERK.Xn
Theoretical instantaneous jerk value R R R
To Next Page
Loading...
