COMMAND OVERVIEW
17
Configure
:CONFigure:VOLTage:ON .......................................... 34
:CONFigure:VOLTage:RANGe ................................... 35
:CONFigure:VOLTage:LATch ..................................... 35
:CONFigure:AUTO:LOAD .......................................... 36
:CONFigure:AUTO:MODE ......................................... 37
:CONFigure:SOUND .................................................. 37
:CONFigure:REMote ................................................... 38
:CONFigure:SAVE ....................................................... 38
:CONFigure:LOAD ...................................................... 38
:CONFigure:PROTection:CURRent:STATe ................ 39
:CONFigure:PROTection:CURRent:LEVel .................. 40
:CONFigure:PROTection:VOLTage:STATe ................ 41
:CONFigure:PROTection:VOLTage:LEVel .................. 41
:CONFigure:PROTection:POWer:STATe .................... 42
:CONFigure:PROTection:POWer:LEVel ..................... 43
:CONFigure:PROTection:UVP:CLEar ......................... 43
:CONFigure:PROTection:UVP:LEVel.......................... 44
Utility
:UTILITY:AUTO:LOAD ................................................ 45
:UTILITY:AUTO:MODE .............................................. 46
:UTILITY:SOUNd ........................................................ 46
:UTILITY:REMote ........................................................ 47
:UTILITY:REMote:MODE ........................................... 47
:UTILITY:TIME ............................................................ 48
:UTILITY:LOAD ........................................................... 48
PEL-2000 Programming Manual
18
Current
:CURRent:STATic:L1/L2 .............................................. 50
:CURRent:STATic:RISE/FALL ...................................... 51
:CURRent:STATic:LOW:AVALue/BVALue ................... 52
:CURRent:STATic:LOW:RISE/FALL ............................. 53
:CURRent:STATic:HIGH:AVALue/BVALue ................. 54
:CURRent:STATic:HIGH:RISE/FALL ........................... 55
:CURRent:DYNamic:L1/L2 .......................................... 56
:CURRent:DYNamic:RISE/FALL .................................. 57
:CURRent:DYNamic:T1/T2 .......................................... 57
:CURRent:DYNamic:LOW:L1/L2 ................................. 58
:CURRent:DYNamic:LOW:RISE/FALL ........................ 59
:CURRent:DYNamic:LOW:T1/T2 ................................ 60
:CURRent:DYNamic:HIGH:L1/L2 ............................... 61
:CURRent:DYNamic:HIGH:RISE/FALL ....................... 62
:CURRent:DYNamic:HIGH:T1/T2 .............................. 63
Fetch
:FETCh:VOLTage? ........................................................ 64
:FETCh:CURRent? ........................................................ 64
:FETCh:POWer? ........................................................... 65
:FETCh:STATus? .......................................................... 65
:FETCh:ALLVoltage? .................................................... 65
:FETCh:ALLCurrent? .................................................... 66
:FETCh:ALLPower? ....................................................... 66
Load
:LOAD:[STATe] ............................................................. 68
:LOAD:SHORt:[STATe] ................................................ 68
:LOAD:SHORt:KEY ...................................................... 69
:LOAD:PROTection? .................................................... 70
:LOAD:PROTection:CLEar ........................................... 70
:LOAD:TIME? ............................................................... 70
To Next Page
Loading...
