EasyManuals Logo

HP HPE FlexNetwork 7500 series User Manual

HP HPE FlexNetwork 7500 series
592 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #341 background imageLoading...
Page #341 background image
329
•
Configure a static route to interface loopback 0 on Switch C (or use a routing protocol like OSPF)
to establish the IBGP connection.
On Switch C:
•
Establish an EBGP connection with Switch A and an IBGP connection with Switch B.
•
Configure BGP to advertise network 9.1.1.0/24 to Switch A, so that Switch A can access the
intranet through Switch C.
•
Configure a static route to interface loopback 0 on Switch B (or use another protocol like OSPF)
to establish the IBGP connection.
Configure load balancing on Switch A.
Configuration procedure
1. Configure IP addresses for interfaces. (Details not shown.)
2. Configure BGP connections:
# Configure Switch A.
<SwitchA> system-view
[SwitchA] bgp 65008
[SwitchA-bgp-default] router-id 1.1.1.1
[SwitchA-bgp-default] peer 3.1.1.1 as-number 65009
[SwitchA-bgp-default] peer 3.1.2.1 as-number 65009
[SwitchA-bgp-default] address-family ipv4 unicast
[SwitchA-bgp-default-ipv4] peer 3.1.1.1 enable
[SwitchA-bgp-default-ipv4] peer 3.1.2.1 enable
[SwitchA-bgp-default-ipv4] network 8.1.1.0 24
[SwitchA-bgp-default-ipv4] quit
[SwitchA-bgp-default] quit
# Configure Switch B.
<SwitchB> system-view
[SwitchB] bgp 65009
[SwitchB-bgp-default] router-id 2.2.2.2
[SwitchB-bgp-default] peer 3.1.1.2 as-number 65008
[SwitchB-bgp-default] peer 3.3.3.3 as-number 65009
[SwitchB-bgp-default] peer 3.3.3.3 connect-interface loopback 0
[SwitchB-bgp-default] address-family ipv4 unicast
[SwitchB-bgp-default-ipv4] peer 3.1.1.2 enable
[SwitchB-bgp-default-ipv4] peer 3.3.3.3 enable
[SwitchB-bgp-default-ipv4] network 9.1.1.0 24
[SwitchB-bgp-default-ipv4] quit
[SwitchB-bgp-default] quit
[SwitchB] ip route-static 3.3.3.3 32 9.1.1.2
# Configure Switch C.
<SwitchC> system-view
[SwitchC] bgp 65009
[SwitchC-bgp-default] router-id 3.3.3.3
[SwitchC-bgp-default] peer 3.1.2.2 as-number 65008
[SwitchC-bgp-default] peer 2.2.2.2 as-number 65009
[SwitchC-bgp-default] peer 2.2.2.2 connect-interface loopback 0
[SwitchC-bgp-default] address-family ipv4 unicast
[SwitchC-bgp-default-ipv4] peer 3.1.2.2 enable

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP HPE FlexNetwork 7500 series and is the answer not in the manual?

HP HPE FlexNetwork 7500 series Specifications

General IconGeneral
BrandHP
ModelHPE FlexNetwork 7500 series
CategorySwitch
LanguageEnglish

Related product manuals