Icom ID-52A

12
SET MODE
12-22
Function
VOX (Default: OFF)
[MENU] > SET > Function > VOX > VOX
Turns the Voice Operated Transmission (VOX)
function ON or OFF�
The VOX function starts transmission without pushing
[PTT] when you speak into the microphone, and
then, automatically returns to receive when you stop
speaking�
• OFF: Turns OFF the function�
• ON: Starts transmission without pushing [PTT]
when you speak into the microphone� Then
automatically returns to receive when you
stop speaking�
VOX Level (Default: 5)
[MENU] > SET > Function > VOX > VOX Level
Sets the VOX gain level to between 1 and 10, or OFF�
Higher values make the VOX function more sensitive
to your voice�
• OFF: Turns OFF the VOX function�
• 1 ~ 10: 1 (The minimum sensitivity)
10 (The maximum sensitivity)
VOX Delay (Default: 0�5sec)
[MENU] > SET > Function > VOX > VOX Delay
Sets the VOX Delay to 0�5, 1�0, 1�5, 2�0, 2�5, or 3�0
seconds� The VOX Delay is the amount of time the
transmitter stays ON after you stop speaking, before
the VOX switches to receive�
VOX Time-Out Timer (Default: 3min)
[MENU] > SET > Function > VOX >
VOX Time-Out Timer
Sets the VOX Time-Out Timer to prevent an accidental
prolonged transmission� To disable the function, set to
“OFF�”
• OFF: Turns OFF the function�
• 1, 2, 3, 4, 5, 10, or 15min:
If a continuous transmission exceeds the set
period of time, the transmission is stopped�
Headset Select (Default: Other)
[MENU] > SET > Function > VOX > Headset Select
Selects the headset type to be connected�
• HS-95: Select when using the HS-95�
• Other: Select when using the HS-94 or HS-97�
CI-V Address (Default: A6)
[MENU] > SET > Function > CI-V > CI-V Address
Sets the CI-V address in hexadecimal code�
L To distinguish devices, each CI-V transceiver has its own
Icom standard address� “A6” is the default address of
the ID-52A/ID-52E� When 2 or more ID-52A/ID-52Es are
simultaneously controlled by a PC, set a different address
for each transceiver between 02 and DF (hexadecimal)�
CI-V Baud Rate (SP Jack) (Default: Auto)
[MENU] > SET > Function > CI-V >
CI-V Baud Rate (SP Jack)
Sets the CI-V data transfer speed when remotely
controlling the transceiver through the [SP] jack,
to 4800, 9600, 19200 bps, or Auto� When “Auto” is
selected, the baud rate is automatically set according
to the controller’s data rate�
CI-V Transceive (Default: OFF)
[MENU] > SET > Function > CI-V > CI-V Transceive
Turns the Transceive function ON or OFF�
L To use the RS-MS1A or RS-MS1I, set to “ON�”
• OFF: The status is not output�
• ON: The status is output� When you change
a transceiver setting, the same change
is automatically set on other connected
transceivers or receivers, and vice versa�
CI-V USB/Bluetooth→REMOTE Transceive
Address (Default: 00)
[MENU] > SET > Function > CI-V >
CI-V USB/Bluetooth→REMOTE Transceive Address
If you remotely operate your transceiver through a
USB cable or using Bluetooth when “CI-V Transceive”
is set to ON, the devices in the same system are also
externally controlled through the [SP] jack�
To prohibit the external control of an Icom transceiver,
set this value to other than “00�”
The control signal is output from the [SP] jack�
Select an address between 00 and DF
(hexadecimal)�