EasyManuals Logo

Juniper EX3400 Features Guide

Juniper EX3400
476 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #363 background imageLoading...
Page #363 background image
interfaces-vlan—(Optional) Clear the binding state on the interface VLAN ID and S-VLAN
ID.
interfaces-wildcard—(Optional) Clear bindings on a set of interfaces. This option supports
the use of the wildcard character (*).
logical-system logical-system-name—(Optional) Clear the binding state for DHCP
clients on the specified logical system.
routing-instance routing-instance-name—(Optional) Clear the binding state for DHCP
clients on the specified routing instance.
dual-stack—(Optional) Remove either both arms or single arm of dual-stack.
NOTE:
The dual-stack command is added in the syntax removes both arms
of the dual-stack with a single command entry.
When the dual-stack command is not added in the syntax, the clear
dhcpv6 server binding command clears only the family specific arm of
the dual-stack.
Required Privilege
Level
view
Related
Documentation
Clearing DHCP Bindings for Subscriber Access
show dhcp server binding on page 378
List of Sample Output clear dhcp server binding <ip-address> on page 343
clear dhcp server binding all on page 344
clear dhcp server binding interface on page 344
clear dhcp server binding <interfaces-vlan> on page 344
clear dhcp server binding <interfaces-wildcard> on page 344
clear dhcp server binding dual-stack all on page 344
Output Fields See show dhcp server binding for an explanation of output fields.
Sample Output
clear dhcp server binding <ip-address>
The following sample output displays the address bindings in the DHCP client table on
the extended DHCP local server before and after the clear dhcp server binding command
is issued.
user@host> show dhcp server binding
343Copyright © 2017, Juniper Networks, Inc.
Chapter 14: Operational Commands (DHCP and DHCP Relay)

Table of Contents

Other manuals for Juniper EX3400

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper EX3400 and is the answer not in the manual?

Juniper EX3400 Specifications

General IconGeneral
Switch typeManaged
Switch layerL2/L3
Quality of Service (QoS) supportYes
SafetyUL-UL60950-1, C-UL CAN/CSA 22.2 No.60950-1, TUV/GS to EN 60950-1, CB-IEC60950-1, EN 60825-1
Form factor1U
Product colorBlack
Electromagnetic compatibilityFCC 47CFR 15 A, EN 55022 A, ICES-003 A, VCCI A, AS/NZS CISPR 22 A, CISPR 22 A, EN 55024, EN 300386, CE
SFP+ module slots quantity4
QSFP+ module slots quantity2
Installed SFP+ modules quantity0
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity48
Memory typeDRAM
Noise level35 dB
Flash memory2000 MB
Processor frequency1000 MHz
Virtual stacking (units)10
Throughput250 Mpps
Jumbo frames9216
MAC address table32000 entries
Number of VLANs4093
Networking standardsIEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3u, IEEE 802.3z
Virtual LAN featuresPort-based VLAN
Copper ethernet cabling technology10BASE-T, 100BASE-T, 1000BASE-T
Power consumption (max)120 W
Number of power supply units1
Operating altitude0 - 3048 m
Non-operating altitude3048 - 4877 m
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 45 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)10 - 85 %
DHCP featuresDHCP server, DHCP client
AuthenticationMAC-based authentication, Port-based authentication
Security algorithms802.1x RADIUS, HTTPS, SNMP, SSH-2
Fiber ethernet cabling technology1000BASE-X
Weight and Dimensions IconWeight and Dimensions
Depth350 mm
Width437 mm
Height44 mm
Weight5740 g

Related product manuals