IFX (Insert effects) List 049: Comp-P4EQ (Compressor - Parametric 4-Band EQ)
109
049: Comp-P4EQ (Compressor -
Parametric 4-Band EQ)
Thiseffectcombinesamonocompressorandafour‐band
parametricequalizer.Youcanchangetheorderofthe
effects.
050: Comp-Phsr (Compressor -
Phaser)
Thiseffectcombinesamonocompressorandaphaser.You
canchangetheord er oftheeffe cts.
Output Mode
WhenWetInvertisselected,therightchannelphaseofthe
chorus/flangereffectsoundisinverted.Thiscreatespseudo‐
stereoeffectsandaddsspread.
However,ifamono‐inputtypeeffectisconnectedafterthis
effect,theleftandrightsoundsmaycanceleachother,
eliminatingthechorus/flangereffects.
Full
parameter
Quick
parameter
Value Explanation
Compressor
Sensitivity C Sens 1...100
Sets the sensitivity
p.83
Attack C Attack 1...100
Sets the attack level
p.83
Level C Level 0...100
Sets the compressor
output level p.83
Parametric 4-Band EQ
Trim E Trim 0...100
Sets the parametric
EQ input level
Band1
Cutoff [Hz]
E1 F[Hz] 20...1.00k
Sets the center
frequency of Band 1
Band1 Q E1 Q 0.5...10.0
Sets the bandwidth of
Band 1 p.87
Band1
Gain [dB]
E1 G[dB] –18...+18
Sets the gain of Band
1
Band2
Cutoff [Hz]
E2 F[Hz] 50...5.00k
Sets the center
frequency of Band 2
Band2 Q E2 Q 0.5...10.0
Sets the bandwidth of
Band 2 p.87
Band2
Gain [dB]
E2 G[dB] –18...+18
Sets the gain of Band
2
Band3
Cutoff [Hz]
E3 F[Hz] 300...10.00k
Sets the center
frequency of Band 3
Band3 Q E3 Q 0.5...10.0
Sets the bandwidth of
Band 3 p.87
Band3
Gain [dB]
E3 G[dB] –18...+18
Sets the gain of Band
3
Band4
Cutoff [Hz]
E4 F[Hz] 500...20.00k
Sets the center
frequency of Band 4
Band4 Q E4 Q 0.5...10.0
Sets the bandwidth of
Band 4 p.87
Band4
Gain [dB]
E4 G[dB] –18...+18
Sets the gain of Band
4
Routing Route
Comp →
P4EQ, P4EQ
→ Comp
Switches the order of
the compressor and
parametric EQ
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
Trim
Parametric 4Band EQ
Output Level
Envelope - Control
Comp
Full
parameter
Quick
parameter
Value Explanation
Compressor
Sensitivity C Sens 1...100
Sets the sensitivity
p.83
Attack C Attack 1...100
Sets the attack level
p.83
Level C Level 0...100
Sets the compressor
output level p.83
Pre EQ Trim 0...100
Sets the EQ input
level
LEQ Gain
[dB]
–15...+15
Sets the gain of Low
EQ
HEQ Gain
[dB]
–15...+15
Sets the gain of High
EQ
Phaser
LFO Freq
[Hz]
P LFO [Hz] 0.02...20.00
Sets the speed of the
LFO
LFO
Waveform
Triangle,
Sine
Selects the LFO
Waveform
Manual P Manual 0...100
Sets the frequency
where the effect is
applied
Depth P Depth 0...100
Sets the depth of LFO
modulation
Resonance P Reso –100...+100
Sets the resonance
amount p.99
Output
Mode
P Out
Normal,
Wet Invert
Selects the phaser
output mode p.109
[Phs] Wet/
Dry
P W/D
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the phaser effect
balance p.91, p.99
[Phs]Source Off...Tempo
Selects the Wet/Dry
modulation source
for the phaser
[Phs]Amount –100...+100
Sets the Wet/Dry
modulation amount
for the phaser
Routing ←
Comp →
Phaser,
Phaser →
Comp
Switches the order of
the compressor and
phaser p.107
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
LEQ HEQ
EQ Trim
Comp
Output Level
Envelope - Control
Phaser
Phaser
Resonance
LFO: Tri / Sine
Phaser Wet / Dry
Normal
Wet Invert
Output Mode
–
+
To Next Page
Loading...
Need help?
General
