Lenze 9300 Servo PLC - Page 173

9300 Servo PLC
Appendix
4-38

9300ServoPLC EN 1.4
Monitoring functions
Heatsink monitoring OH (fixed), 2-63
Heatsink monitoring OH4 (adjustable), 2-63
Plant speed monitoring NMax, 2-64
Motor control, 2-48
O
Operation inhibited(DISABLE), 2-27
Outputs_AIF1 (AIF1_OUT), 2-7
Outputs_AIF2 (AIF2_OUT), 2-12
Outputs_AIF3 (AIF3_OUT), 2-17
Outputs_ANALOG1 (AOUT1), 2-22
Control terminals, Assignment, 2-22
Outputs_ANALOG2 (AOUT2), 2-24
Control terminals, Assignment, 2-24
Outputs_CAN2 (CAN2_OUT), 3-16
Outputs_CAN3 (CAN3_OUT), 3-20
Outputs_DIGITAL (DIGOUT), 2-44
Overcurrent diagram, 2-61
Overvoltage, 2-58
P
Parameter channels, 3-7
Parameterization, CAN-bus, 3-43
Phase controller, Phase controller influence, 2-53
Plant speed monitoring NMax, 2-64
PLC functionality, 4-1
Prefix, Explanation of, 1-3
Process data, 3-48
Process data channels, 3-8
cyclic, 3-8
event-controlled, 3-9
Process-data objects, 3-49
event-controlled, 3-52
PTCOverTemp, 2-61
Q
Quick stop (QSP), 2-54
Quickstop (QSP), 2-27
R
Rapidstop(Quickstop), 2-54
Reset, Fault message, 4-14
S
Safety information, Layout
Other notes, 1-1
Warning of damage to material, 1-1
Set integral component, 2-52
ShortCircuit, 2-59
Signal type, Explanation of, 1-5
Speed controller, 2-51
Set integral component, 2-52
Statebus (STATEBUS_IO), 2-65
Status messages, 4-8
Status signals, digital output, 2-29
Status word, 4-8
Sync-Management, 3-25
Synchronization of control program cycles, 3-25
System blocks
absolute addresses, 2-2
Analog inputs and outputs (ANALOG_IO), Outputs_ANALOG2_IO
(AOUT2), 2- 24
Automation interface (AIF1_IO), 2-4
Automation interface (AIF2_IO), 2-10
Automation interface (AIF3_IO), 2-15
CAN_Management, 3-22
Digital frequency input (DF_IN), 2-31
Technical data for connection, 2-35
Digital frequency output (DF_OUT), 2-38
T, 2-42
Drive control (DCTRL_DriveControl), 2-25
Controllerinhibit (CINH), 2-28
Operation inhibited(DISABLE), 2-27
output digital status signals, 2-29
Quickstop (QSP), 2-27
TRIP-RESET, 2-28
TRIP-SET, 2-28
Free codes (FCODE), 2-45
Inputs_ANALOG1 (AIN1), 2-21
Inputs_ANALOG2 (AIN2), 2-23
Inputs_DIGITAL (DIGIN), 2-44
Module numbers, 2-2
Outputs_AIF2 (AIF2_OUT), 2-12
Outputs_ANALOG1 (AOUT1), 2-22
Statebus (STATEBUS_IO), 2-65
System markers (SYSTEM_FLAGS), 2-67
Show/Hide Bookmarks