Troubleshooting and fault elimination
10.3 Fault messages
10-8
L
EDSVS9332S-E EN 3.0
Error
code
RemedyCauseErrorFault number
x=0:TRIP
x = 1: Message
x = 2: Warning
P09 x159 Impermissible
programming
Impermissible programming Check position program:
• A PS with final speed must be followed by a PS
with positioning; it is not permissible to wait for
input.
P12 x162 Encoder range The range of the absolute encoder was exceeded. • Return drive by manual positioning.
• Check position limits and adjustment of the
encoder.
• The absolute encoder has to be dimensioned
and mounted such that its range is not exceeded
over the complete positioning range.
P13 x163 Phase overflow • Phase controller limit reached
• Drive cannot follow the digital frequency (I
max
limit).
• Enable drive
• Check drive dimensioning
P14 x164 1st following error The drive cannot follow the setpoint. The following
error is greater than the limit value in C1218/1.
• Increase current limit C0022 (observe max.
motor current).
• Reduce acceleration.
• Check drive dimensioning.
• Increase limit value under C1218.
P15 x165 2nd following error The drive cannot follow the setpoint. The following
error is greater than the limit value in C1218/2.
• Increase current limit C0022 (observe max.
motor current).
• Reduce acceleration.
• Check drive dimensioning.
• Increase limit value under C1218.
P16 x166 Transmission error of a
sync telegram on the
Sync telegram from master (PLC) is out of time
pattern.
Set C1121 (Sync cycle) to the transmission cycle of
the master (PLC).
system bus.
Sync telegram of master (PLC) is not received. • Check communication channel.
• Check baud rate, controller address.
Controller enable (RFR) too soon. Enable the controller with a delay. The required time
delay depends on the intervals between the sync
telegrams.
* C0362 displays the interval between two 2 sync telegrams (C0362 = 0, communication interrupted).
P17 x167 TP control error Different function blocks use the TP input at the
same time (e. g. FB DFSET and POS). A conflict
arises.
Configure another TP input for FB POS (not possible
for DFSET) or switch off monitoring under C0580.
P18 x168 Internal limitation
The data generated by calculations of the 9300 servo position controller cannot be varied arbitrarily. If the
values exceed or fall below the internal limit values, the warning ”P18” is displayed and the set value is
limited to the minimum or maximum respectively.
C1298 = 1:
The negative position limit in C1223 is outside the
possible display range of
1 ≤ (C1223 × C1205) ≤ 1.07E9 inc
Check entries in C1202-4, C1207/1, C1207/2. If
necessary, read out the value reduced with
C1220/10 at malfunction and use it to overwrite the
value entered in C1223.
C1298 = 2:
The positive position limit in C1224 is outside the
possible display range of
1 ≤ (C1224 × C1205) ≤ 1.07E9 inc
Check entries in C1202-4, C1207/1, C1207/2. If
necessary, read out the value reduced with C1224
at malfunction and use it to overwrite the value
entered in C1124.
C1298 = 3:
The maximum speed v
max
under C1240 exceeds
the possible display range of
1 ≤ (C1240 × C1205 × 16.384) ≤ 2.14E9 inc or
v
max
not C1240 / C1204 × 60 ≤ 1.5 × n
max
Check entries in C0011, C1202-4, C1207/1,
C1207/2. If necessary, read out the value reduced
with C1220/12 at malfunction and use it to
overwrite the value entered in C1240 or adapt the
value in C1240 to C0011.
C1298 = 4:
The maximum acceleration a
max
in C1250 exceeds
the possible display range of
1 ≤ (C1250 × C1205 × 16.384 / 1000)
≤ 2.8634E7 inc
Check entries in C1202-4, C1207/1, C1207/2. If
necessary, read out the value reduced with
C1220/13 at malfunction and use it to overwrite the
value entered in C1250.
C1298 = 5:
An internal value range has been exceeded for a
speed standardisation. Valid range:
1 ≤ (C0011 × C1207/1 / C1207/2 × 65536 / 60000)
≤ 32767
Check entries in C0011, C1207/1, C1207/2.
To Next Page
Loading...