Mindray iPM-9800

To Next Page

To Previous Page

Company Contact

Manufacturer: Shenzhen Mindray Bio-Medical Electronics Co., Ltd.

E-mail Address: service@mindray.com

Tel: +86 755 26582479 26582888

Fax: +86 755 26582934 26582500

EC-Representative: Shanghai International Holding Corp. GmbH(Europe)

Address: Eiffestraβe 80, Hamburg 20537, Germany

Tel: 0049-40-2513175

Fax: 0049-40-255726

Main Page

Default Chapter8
- Intended Audience8
- Table of Contents9
1 Safety19
- Safety Information19
- Equipment Symbols22
2 The Basics23
- Monitor Description23
- Main Unit24
- Display Screen28
- Quickkeys30
3 Basic Operations31
- Installation31
  - Unpacking and Checking32
  - Environmental Requirements32
- Getting Started33
- Disconnecting from Power34
- Operating and Navigating34
- Operating Modes37
- Using an External Storage Device38
- Using an External Display39
- Changing General Measurement Settings39
- Changing General Settings40
4 Managing Patients45
- Admitting a Patient45
- Editing Patient Information46
- Discharging a Patient46
- Switching between Wire and Wireless Networks47
- Transferring Patient Data47
- Connecting to a Central Monitoring System49
5 Managing Configurations51
- Introduction51
- Entering and Exiting the Configuration Mode52
- Viewing and Changing Configurations53
- Adding a Configuration54
- Deleting a Configuration54
- Loading a Configuration55
- Setting Default Configuration at Startup55
- Loading the Latest Configuration Automatically56
- Transferring a Configuration57
6 User Screens59
- Tailoring Your Screens59
- Viewing Minitrends61
- Viewing Oxycrg63
- Viewing Other Patients64
- Understanding the Big Numerics Screen66
7 Alarms67
- Alarm Categories67
- Alarm Levels68
- Alarm Indicators68
- Understanding Alarm Statuses70
- Alarm Configuration72
- Latching Alarms75
- Clearing Technical Alarms76
- Testing Alarms76
- When an Alarm Occurs76
- Using Care Group Alarms77
8 Monitoring ECG79
- Introduction79
- Safety79
- Preparing to Monitor ECG80
- Understanding the ECG Display85
- Changing ECG Settings86
- About ST Monitoring90
- About Arrhythmia Monitoring93
- 12-Lead ECG Monitoring99
9 Monitoring Respiration (Resp)103
- Introduction103
- Safety103
- Placing Resp Electrodes103
- Understanding the Resp Display105
- Changing Resp Settings105
10 Monitoring PR109
- Introduction109
- Changing PR Settings109
11 Monitoring Spo111
- Introduction111
- Safety112
- Identifying Spo Modules112
- Applying the Sensor112
- Changing Spo Settings113
- Measurement Limitations116
- Masimo Information116
- Nellcor Information117
12 Monitoring NIBP119
- Introduction119
- Safety120
- Measurement Limitations120
- Setting up the NIBP Measurement121
- Measurement Methods122
  - Enabling NIBP Auto Cycling and Setting the Interval122
  - Starting a STAT Measurement122
- Understanding the NIBP Numerics123
- Changing NIBP Settings124
- Assisting Venous Puncture125
- Resetting NIBP125
- NIBP Leakage Test125
- NIBP Accuracy Test126
- Calibrating NIBP127
13 Monitoring Temp129
- Introduction129
- Safety129
- Making a Temp Measurement129
- Understanding the Temp Display130
- Setting the Temperature Unit130
14 Monitoring IBP131
- Introduction131
- Safety131
- Setting up the Pressure Measurement131
- Understanding the IBP Display133
- Changing IBP Settings134
- Measuring PAWP136
  - Preparing to Measure PAWP136
  - Setting up the PAWP Measurement138
- Zeroing the Transducer139
15 Monitoring Cardiac Output141
- Introduction141
- Understanding the C.O. Display141
- Influencing Factors142
- Setting up the C.O. Measurement142
- Measuring the Blood Temperature145
- Changing C.O. Settings146
  - Setting the Temperature Unit146
  - Setting the Interval between Measurements146
16 Monitoring Carbon Dioxide147
- Introduction147
- Preparing to Measure CO148
- Setting Barometric Pressure Compensation154
- Removing Exhaust Gases from the System155
- Calibrating the Sensor156
17 Monitoring AG157
- Preparing to Measure AG158
- Understanding the AG Display160
- MAC Values161
- Changing AG Settings162
  - Entering the Standby Mode163
  - Measurement Limitations164
- Removing Exhaust Gases from the System165
18 Freezing Waveforms167
- Unfreezing Waveforms168
- Review169
19 Review170
- Reviewing Graphic Trends170
- Reviewing Tabular Trends172
- Reviewing NIBP Measurements174
- Reviewing Alarms175
- Reviewing Waveforms176
20 Calculations179
- Dose Calculations180
  - Titration Table181
  - Entered Parameters182
- Ventilation Calculations183
  - Calculated Parameters184
  - Entered Parameters185
- Renal Calculations186
  - Calculated Parameters187
- Recording189
21 Recording190
- Overview of Recording Types190
- Starting and Stopping Recordings191
  - Setting the Realtime Recording Length192
- Removing Paper Jam193
- Cleaning the Recorder Printhead194
22 Printing195
- Starting Report Printouts196
- Stopping Report Printouts197
  - Setting up Graphic Trends Reports198
- Printer Statuses199
23 Other Functions201
- Transferring Data202
- Nurse Call203
- Wireless Network205
24 Batteries207
- Installing or Replacing a Battery208
- Battery Guidelines209
- Battery Maintenance210
- Battery Recycling211
25 Care and Cleaning213
- Cleaning214
26 Maintenance215
- Service Tasks216
- Calibrating ECG217
- Calibrating CO2218
- Calibrating AG219
- Setting up IP Address220
27 Accessories221
- Spo2 Accessories223
- NIBP Accessories225
- Temp Accessories226
- C.O. Accessories228
- AG Accessories231
- Others232
  - Product Specifications233
  - Alarm Messages285

Mindray iPM-9800 - Page 7

Table of Contents

Other manuals for Mindray iPM-9800

Related product manuals