In a KSU View Package or Terminal Drag & Drop can work only from Package or Terminal Panel. This
screen also shows system configuration after download the database from the system and can review
each settings or make additional changes.
KSU View provides following functionalities listed in Table 1-60 KSU View Function List on
page 1-592.
Table 1-60 KSU View Function List
Feature Name Description
Package Drag & Drop When select Package panel at Slide Panel, line up of Packages are listed. Packages can be con-
figured by drag & drop the required package from this panel to required slot in a KSU View.
Terminal Drag & Drop When select Terminal panel at Slide Panel, line up of Terminals are listed. Terminals can be con-
figured by drag & drop the required Terminal from this panel to required port in a KSU View.
Data Setting By clicking H/W figure in a KSU View, the screen changes to Data Setting menu at Main View.
Then individual data setting related to specific H/W can be set. See detail in Table 1-61 Intuition
Setup HW Setting on page 1-592.
Data Marking This function marks the Trunk, Terminal or Device figure to pink which was changed at Data Set-
ting.
* This change history marking works only when changed the data at Intuition Setup.
Bitmap Highlight When mouse move over the H/W figure in KSU View the H/W figure is Highlighted.
Ex/Trk Free Port List Indicate Free extension or trunk number as remaining Port. This number is increased or de-
creased when configuration is changed at KSU View automatically.
Unused Ext/Trunk In MLT, if PRG 10-03(ESI)-01 Terminal Type is set to "No Setting" in KSU View all the extension
port are showed in Gray Color.
In Analog line, if PRG 90-06 Trunk Control is set to "0: Set Busy Out" in KSU View all trunk lines
are showed in Gray Color.
Data Setting
By clicking H/W figure in a KSU View, the screen jumps to Data Setting for each H/W and related
Programs to be assigned. This Data Setting can be also entered from Navigation Bar, Data Link
screen. Before any data has been changed, H/W Data link icons are not indicated.
Table 1-61 Intuition Setup HW Setting
Link Description System Data Note
MLT Indicate Icon, Name and
number of MLT
PRG 11-02-01: Extension Numbering
PRG 15-01-01: Extension Name
PRG 15-02-01: Display Language Selection
PRG 15-02-02: Trunk Ring Tone
PRG 15-02-03: Extension Ring Tone
PRG 15-01-02: Outgoing Trunk Line Preference
PRG 15-02-09: Auto Answer to Incoming Call from Extension
PRG 15-02-68: Voice/Signal selection for ICM call (Supported at
PCpro only)
PRG 10-03-12 (ESI): Number of Line Key selection (Supported at
PCpro only)
SLT Indicate Icon, Name and
number of SLT
PRG 11-02-01: Extension Numbering
PRG 15-01-01: Extension Name
PRG 15-03-01: SLT Signaling Type
PRG 15-01-02: Outgoing Trunk Line Preference
PRG 15-03-09: Caller ID Function - For extension
Door-
phone
Indicate Icon, Name and
number of Doorphone
PRG 32-04-01: Doorphone Name
DSS Indicate Icon, Name and
number of DSS
PRG 30-02-01: Extension Number
Analog
Line
Indicate Icon, Name and
number of Line
PRG 14-01-01: Trunk Name
PRG 14-02-01: Signaling Type
PRG 14-02-09: Busy Tone Detection
PRG 14-02-10: Caller ID
PRG 22-04/22-05: IRG settings
SL1100 ISSUE 2.0
1-592
PC Programming - Intuition Setup
P
To Next Page
Loading...
