xii Table of Contents
Figure 4-13 Conveyor I/O (Outputs 0-31) ............................................................................................4-19
Figure 4-14 Conveyor I/O (Inputs 0-31) ...............................................................................................4-20
Figure 4-15 Setup Conveyors ..............................................................................................................4-23
Figure 4-16 Dispenser I/O (Outputs 0-31) ...........................................................................................4-24
Figure 4-17 FmXP Jog Window ...........................................................................................................4-25
Figure 4-18 Vision and Reticles Set-up Dialog Boxes ......................................................................... 4-27
Figure 4-19 Machine Offsets Parameters Dialog Box..........................................................................4-30
Figure 4-20 Dispenser I/O (Inputs 0-31) ..............................................................................................4-31
Figure 4-21 Dispenser I/O Test (Outputs 32-63) .................................................................................4-32
Figure 4-22 Service Station..................................................................................................................4-33
Figure 4-23 Scale Setup ......................................................................................................................4-34
Figure 4-24 Heater Control Window ....................................................................................................4-36
Figure 4-25 Valve Offset Dialog Boxes................................................................................................4-39
Figure 4-26 Machine Setup Dialog Box ...............................................................................................4-40
Figure 4-27 Program Open Window ....................................................................................................4-41
Figure 4-28 Run Window .....................................................................................................................4-41
Figure 5-1 Focusing the Camera .........................................................................................................5-2
Figure 5-2 FmXP Setup Vision.............................................................................................................5-3
Figure 5-3 FmXP Calibration Window..................................................................................................5-4
Figure 5-4 Adjusting the Service Station Height ..................................................................................5-5
Figure 5-5 Scale Cover Removal.........................................................................................................5-6
Figure 5-6 Leveling the Scale ..............................................................................................................5-6
Figure 5-7 Setup Scale - Scale Operations Tab ..................................................................................5-7
Figure 5-8 Setup Scale - Advanced Tab..............................................................................................5-7
Figure 5-9 FmXP Calibrating Scale Message......................................................................................5-8
Figure 5-10 FmXP Calibration Complete Message ............................................................................... 5-8
Figure 5-11 Z-head Counter Balance Force Adjustment .......................................................................5-9
Figure 5-12 Adjusting the Height Sensor Probe ..................................................................................5-10
Figure 5-13 Board Sensor - Side View ................................................................................................5-11
Figure 5-14 Board Sensor - Top View .................................................................................................5-11
Figure 5-15 Initializing the Digital Gauge .............................................................................................5-13
Figure 5-16 Beacon Configuration Dialog Box.....................................................................................5-14
Figure 5-17 Beacon Configuration Dialog Box.....................................................................................5-15
Figure 5-18 Dispenser I/O Dialog Box .................................................................................................5-15
Figure 6-1 Valve Pneumatic and Electrical Connections (DV-8000 shown)........................................ 6-2
Figure 6-2 Valve Pneumatic and Electrical Connections (DJ-9000 shown) ........................................ 6-3
Figure 6-3 Main Air Pressure Regulator and Gauge Sets ...................................................................6-4
Figure 6-4 Adjusting the Valve and Fluid Pressure Regulators ...........................................................6-5
Figure 6-5 Low Air Pressure Detection Window ..................................................................................6-6
Figure 6-6 Setup Valve Offsets Dialog Box .........................................................................................6-7
Figure 6-7 FmXP Error Message 30694 ..............................................................................................6-8
Figure 6-8 Production Window - Teaching Safe Z Height ...................................................................6-9
Figure 6-9 Teaching Safe Z Height......................................................................................................6-9
Figure 6-10 Conveyor Position Controls ..............................................................................................6-10
Figure 6-11 Dispensing Head Position Controls ..................................................................................6-12
Figure 6-12 Conveyor Position Controls ..............................................................................................6-15
Figure 6-13 Camera LED's (Rear View) ..............................................................................................6-16
Figure 6-14 Camera Lighting Adjustment ............................................................................................6-18
Figure 6-15 Fluidmove Production Window .........................................................................................6-20
Figure 6-16 Heater Control Window ....................................................................................................6-21
Figure 6-17 FmXP Fluid Manager........................................................................................................6-22
Figure 6-18 Workpiece Alignment Options ..........................................................................................6-23
Figure 6-19 Create Workpiece .............................................................................................................6-24
Figure 6-20 Machine Setup Window....................................................................................................6-25
Figure 6-21 Programming Window ......................................................................................................6-26
Figure 6-22 Program Commands Toolbar ...........................................................................................6-27
To Next Page
Loading...
Need help?
General