Parker 591C - Page 216

590 Series DC Digital Drive Parameter Specification Tables
C-5
Tag Mn Function Block Name Parameter Name Minimum Maximum Default Units Range Notes
31 av CURRENT PROFILE SPD BRK2 (HIGH) 0.0 100.0 100.0 % V0 W1
32 aw CURRENT PROFILE SPD BRK1 (LOW) 0.0 100.0 100.0 % V0 W1
33 ax CURRENT PROFILE IMAX BRK2(SPD2) 0.0 200.0 200.0 % V0 W1
37 b1 MENUS VIEW LEVEL 0 2 1 0: BASIC
1: STANDARD
2: ADVANCED
V0 W0
39 b3 CONFIGURE DRIVE CONFIGURE ENABLE 0 1 0 0: DISABLED
1: ENABLED
V0 W1
41 b5 SPEED LOOP SETPOINT 4 -105.00 105.00 0.00 % V0 W0
42 b6 CURRENT LOOP AT CURRENT LIMIT 0 1 0 V1 W4
43 b7 DIGITAL OUTPUT 1 MODULUS 0 1 1 V0 W0
44 b8 DIGITAL OUTPUT 2 MODULUS 0 1 1 V0 W0
45 b9 DIGITAL OUTPUT 3 MODULUS 0 1 1 V0 W0
47 bb SPEED LOOP SPEED FBK SELECT 0 3 0 0: ARM VOLTS FBK
1: ANALOG TACH
2: ENCODER
3: ENCODER/ANALOG
V0 W1
48 bc CURRENT LOOP NEG. I CLAMP IN -100.00 100.00 -100.00 % V1 W0
49 bd ENCODER 1 ENCODER SIGN 0 1 1 0: NEGATIVE
1: POSITIVE
V0 W1
50 be ANALOG INPUT 1 ANIN 1 (A2) 0.00 0.00 0.00 V V1 W4
51 bf ANALOG INPUT 2 ANIN 2 (A3) 0.00 0.00 0.00 V V1 W4
52 bg ANALOG INPUT 3 ANIN 3 (A4) 0.00 0.00 0.00 V V1 W4
53 bh ANALOG INPUT 4 ANIN 4 (A5) 0.00 0.00 0.00 V V1 W4
54 bi ANALOG INPUT 5 ANIN 5 (A6) 0.00 0.00 0.00 V V1 W4
55 bj ANALOG OUTPUT 1 ANOUT 1 (A7) 0.0 0.0 0.0 V V1 W4
56 bk ANALOG OUTPUT 2 ANOUT 2 (A8) 0.0 0.0 0.0 V V1 W4
57 bl CALIBRATION TERMINAL VOLTS 0.0 0.0 0.0 % V1 W4
58 bm CALIBRATION UNFIL.TACH INPUT 0.0 0.0 0.0 % V0 W4
59 bn ENCODER 1 UNFIL.ENCODER 0 0 0 RPM V0 W4
60 bo CALIBRATION BACK EMF 0.0 0.0 0.0 % V0 W4
61 bp CURRENT LOOP ACTUAL NEG I LIM 0.0 0.0 0.0 % V0 W4
62 bq SPEED LOOP UNFIL.SPD.FBK 0.00 0.00 0.00 % V0 W4
63 br SPEED LOOP SPEED SETPOINT 0.00 0.00 0.00 % V0 W4
64 bs SPEED LOOP UNFIL.SPD.ERROR 0.00 0.00 0.00 % V0 W4
65 bt CURRENT LOOP IaFbk UNFILTERED 0.0 0.0 0.0 % V0 W4
66 bu CURRENT LOOP IaDmd UNFILTERED 0.0 0.0 0.0 % V0 W4
67 bv CURRENT LOOP ACTUAL POS I LIM 0.0 0.0 0.0 % V0 W4
68 bw SEQUENCING START (C3) 0 1 0 0: OFF
1: ON
V1 W4