Polyend Tracker - FX Steps

265
Polyend Tracker Manual
264
Polyend Tracker Manual
Performance Mode
12
Performance Mode
12
▌ SETTING A TRACK PATTERN
1. Playback stopped.
2. Press [Perform] to select the Performance Mode page.
3. Hold [Track 1] to [Track 8] Screen button + Turn (Jog). This selects the
pattern assigned to the chosen track. These can also be changed
during playback as a real-time performance and remix technique.
▌ CHANGING PERFORM TEMPLATE SAVE BEHAVIOUR
1. Press [Cong] to open the project conguration menu.
2. Ensure the left window is highlighted red i.e. in focus. Navigate windows
by pressing [Left] or [Right]. Menu windows will automatically be
selected when pressing the relevant screen keys below the window to
navigate [Up] or [Down].
3. Press [Up] [Down] or Turn (Jog) to highlight with the bounding box the
‘Project Settings’ option. Alternatively press the relevant screen keys
below the left window to navigate [Up] or [Down].
4. Press [Up] [Down] or Turn (Jog) to highlight with the bounding box over
the ‘Performance preset’ option in the central window. Alternatively
press the relevant screen keys below the central window to navigate
[Up] or [Down].
5. To change the selected parameter / setting, Press [Change]. The
parameter pop-up window listing the available options will appear.
6. Turn (Jog) or Press [Up] / [Down] or [Up] / [Down] Screen buttons to
highlight the desired option. The ‘Global’ setting will save the perform
template for all projects while ‘Per Project’ will save on an individual
project basis. Global is default.
7. Press [Apply] - 6
th
Screen button to conrm selection or [Cancel] - 3
rd
Screen button to exit without changing.
NOTESNOTES
12.5 Conguring Effects
Effects can be setup in record mode with up to 12 effects being congured
from a library of 21 performance effects. By default the performance preset
is saved on a global basis, but can be changed to be saved ‘per-project’ in
the ‘Cong’ settings.
▌ CREATING AN EFFECT TEMPLATE
1. Press [Perform] to select the Performance Mode page.
2. Press [Rec] to select record mode. Values and bounding box are red.
3. Navigate between effect slots, Press [Left] or [Right].
4. To cycle the effect for the selected slot, Press [Up] or [Down].
5. To swap effects, Hold [Shift] + [Right] or [Left]. This will swap the
currently selected effect along with the values with the slot chosen. The
pad value selections will remain with the original slot. This can also be
used creatively.
6. Hold [PAD] + Turn (Jog) to change the value of the specic effect row.
The selected Pad will be representative of the effect value. Pad row 2 is
the 2
nd
row of effect values, Pad row 3, is 3
rd
row of effect parameters.
Top row 1 is reserved to reset the value to the default.
7. Repeat steps 3 - 5 for other effect slots. 12 slots are available.
8. Press [Rec] to turn record mode off.
Swap Effects
Hold [Shift] + [Right] / [Left]
Select Slot
Press [Right] / [Left]
Pad Row 1
MIDI CC Row
Pad Row 2
Pad Row 3
Pad Row 4
Change Effects
Press [Up] / [Down]
Track 1
Patt: 1
---
---
-100
+100
-50
---
---
-1
-1
-1
---
---
-5
+5
-7
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
>>>
>>>
/16
/16
/16
---
---
-1
-1
-1
Track 2
Patt: 1
Track 3
Patt: 1
Track 4
Patt: 1
Track 6
Patt: 1
Track 5
Patt: 1
Track 7
Patt: 1
Track 8
Patt: 1
Performance FX
Volume High-pass cutoff Sample end Tune Delay send Sample Playback Panning Band-pass cutoff Low-pass cutoff Sample position Reverb send Volume LFO
0m:00s P1.028
Rec