71
Polyend Tracker Manual
70
Polyend Tracker Manual
Manual Step Entry
NOTESNOTES
Sequencing Steps
5
Sequencing Steps
5
Track 1 Track 4Track 3Track 2
Recording mode on to edit steps in the pattern
Steps can be added individually.
Example: Hold [Note] + [PAD] to select an option.
Subsequent steps are recorded when pressing pads.
This will record iteratively the selected parameter into
rows dened by the ‘Step jump’ intervals.
Playing [PAD] in recording mode will record the respective parameter value depending
on 1) the parameter selected for the step and 2) the actual pad number chosen.
Example shows Pad 2 selected.
Note Selected, Pad 3 which represents D6.
Instrument Selected, Pad 3 which represents Instrument #3.
FX1 Selected, FX Effect not applied.
FX2 Selected, Pad 3 which represents effect #3 - Volume = 50.
Quick Tap Dedicated Parameter Button to lock the selection e.g. [Instrument]
Select multiple step rows with [Shift] + [Up] or [Down].
Also across multiple tracks [Shift] + [Left] + [Down]
On the top row [Shift] + [Up] will select all steps in the
track. Press [Shift] + [Up] + [Up] to select all steps.
Edits to any existing parameters can be made
simultaneously, but only If a parameter is already set.
These changes will be relative to the original value.
Unassigned elements of a step will remain empty.
Step Jump
1
Step Jump
2
C5 40
----
P 25
D6 03
----
V 50
D6 03
----
V 50
D6 03
----
V 50
D6 03
----
V 50
D6 03
----
V 10 D6 03
----
V 10
D6 03
----
D6 03
----
----
----
----
----
--- ---
--- ---
V 50
V 30
Steps can be added edited collectively too. Select a range within a track or
across tracks to edit.
▌ MANUALLY EDITING A RANGE OF STEPS
1. Press [Pattern] to select the Pattern Mode page.
2. Select the target step to edit. Use [Up], [Down] or Turn (Jog) to scroll
top to bottom. Press [Left], [Right] to select a track. Example Row 1 of
Track 1. The step should be highlighted with the green bounding box.
3. Press [Shift] + [Left] or [Right] to select across tracks and [Shift] + [Up]
or [Down] to select rows in a track and expand the selection range.
4. To select all steps for a track, select the top step on the track to select,
then Press [Shift] + [Up].
5. To select all steps in the pattern, select the top step on a track, then
Press [Shift] + [Up] + [Up].
6. Press [Rec] to switch to recording mode. The step bounding box will
turn red and allow editing of the collective step range.
7. Press [Preview], 5
th
Screen button, to play only the range of selected
steps. Also press a [PAD] to preview.
8. The Jog function will now change the selected parameter when in
recording mode as opposed to purely navigation in normal play mode.
9. Select a parameter to edit. Only existing parameters can be changed.
Any empty parameter slots will not change and remain open.
• To select Note: Hold [Note] + Select, or Tap [Note] to lock.
• To select Instrument: Hold [Instrument] + Select or Tap [Instrument]
to lock selection of parameter.
• To select FX1: Hold [FX1] + Select or Tap [FX1] to lock selection.
• To select FX1: Hold [FX2] + Select or Tap [FX2] to lock selection.
10. Turn (Jog) to adjust the parameter value of the selected parameter
within the step. Selected parameter will be solid coloured red. When
adjusting simultaneous values they will each change relative to the
original value.
To Next Page
Loading...
