QubicaAMF XLi EDGE Series - Critical Measurements

Critical Measurements
400-088-120-02 4.2-39 Rev. Date: 10/2016
Kickbacks / Pindeck
Distance from back edge of kickback to 7 – 10 Line .................................................................................................................................................
6¼” (159 mm) New / 6¼”–6½” (159–165) Retrofit
Distance from wood part of kickback to center of the #7 and #10 Spots* ..........................................................................................................................................
12
1
/
16
”±
1
/
16
” (12”– 12
1
/
8
”: 305–308 mm)
Distance from wood part of kickback to center of the #1 Spot* .........................................................................................................................................................
30
1
/
16
” ±
1
/
16
” (30”– 30
1
/
8
”: 762–765 mm)
Distance between kickbacks (wood to wood) across Lane* ................................................................................................................................................................
60
1
/
8
” ±
1
/
8
” (60”– 60¼”: 1524–1530 mm)
Distance from top of kickback to Pin Deck surface* ...........................................................................................................................................................................


17” (432 mm)
Dimension of cuts on back of Double Kickback Assembly ...................................................................................................................................................................
4” deep x 7” high (102 x 178 mm)
Flat Gutters
Width of Flat Gutters (includes molding)* ...........................................................................................................................................................................................
9¼” ± ¼” (9”– 9½”: 229–241 mm)
Depth of gutter opposite the #1 Spot* .................................................................................................................................................................................................


1
7
/
8
” (48 mm)
Depth of gutter at point opposite the #7 and #10 Spots*....................................................................................................................................................................
3½” ±
1
/
8
” (3
3
/
8
”– 3
5
/
8
”: 86–92 mm)
Front End
Distance from underside of frame to Pin Deck surface ........................................................................................................................................................................
18
7
/
8
” ±
1
/
8
” (18¾”– 19”: 476–483 mm)
Height difference between corners of frame .......................................................................................................................................................................................
1
/
32
” (1 mm)
Table
Play in respot cell fingers ......................................................................................................................................................................................................................
1
/
4
”–
3
/
8
” (6–9.5 mm) + equal finger to finger
Length of long rod at front of table ......................................................................................................................................................................................................
8
1
/
8
” (206 mm)
Table position (Flags) max deviation from center of #1, #7, & #10 Spots ...........................................................................................................................................
±
1
/
8
” (3 mm)
Gap under table leg screw (cups horizontal) ........................................................................................................................................................................................
3
/
16
” (5 mm)
Gap under table leg screw (cups vertical – spot rod adjustment) .......................................................................................................................................................
1
/
16
”–
3
/
32
” (1.5 –2.5 mm)
Gap between Pawl and point of Shifter Link ........................................................................................................................................................................................
3
/
8
” (9.5 mm)
Table height – Distance between pin deck and screw head ................................................................................................................................................................
5
/
16
” (8 mm)
Shuttle adjustment ...............................................................................................................................................................................................................................
2” (51mm)
Yoke spring position ..............................................................................................................................................................................................................................
Even with top of U-bolt nut
Back End
Distance from front edge of side plate flange to 7–10 Line .................................................................................................................................................................
6½” (165 mm) New / 6½”–6¾” (165–171 mm) Retrofit
7–10 Line
60 – 60 ¼”
(1524-1530
mm)
30 – 30
1
/8”
(762-765
mm)
3
3
/8 –3
5
/8
”
(86-92
mm)
1
7
/8” Min
(48 mm)
12 – 12
1
/8” (305-308
mm)
4”
(102
mm)
7”
(178
mm)
9 –
9½”
(229-241 mm)
6¼
”
(159
mm)
17” Min.
(432 mm)
Extension of
the 7–10
Line
(5
mm)
Long Rod
8-1/8”
(206 mm)
Shifter Link
3/8”
(9.5 mm)
Pawl
Respot Rod
Gap Under Table Leg Screw (Cups Horizontal)
2

1
/
16
inches