Radwin 2000 C PLUS

RADWIN2000CPlusUserManual Release3.5.70 C‐4
MIBParameters ChapterC
<winlink1000><Section1>...<Sectionn><ParameterName>
Foreachoftheconfigurationandcontrolparameters(parameterswithread‐writeaccess),
the“Description”columndescribeswhenthenewvalueiseffective.Itisrecommendedthat
youperformtheappropriateactiontomakethevaluesaff e ctiveimmediatelyafterany
change.Whereachangeisrequiredonbothsidesofthelink,itisrecommendedthatyou
changebothsidesofthelinkfirstandthenperformtheaction.
SupportedVariablesfromtheRFC1213MIB
TableC‐1:SupportedVariables
Name OID Type
Access
Description
ifIndex
.1.3.6.1.2.1.2.2.1.1.x
a
Integer RO Auniquevalueforeachinterface.Itsvalue
rangesbetween1andthevalueof
ifNumber.Thevalueforeachinterfacemust
remainconstantatleastfromonere‐
initializationoftheentity'snetwork
managementsystemtothenextre‐
initialization.
ifDescr .1.3.6.1.2.1.2.2.1.2 DisplayString RO Atextualstringcontaininginformation
abouttheinterface.Thisstringshould
includethe
nameofthemanufacturer,the
productnameandtheversionofthe
hardwareinterface.
ifType .1.3.6.1.2.1.2.2.1.3 Integer RO Thetypeofinterface,distinguished
accordingtothephysical/linkprotocol(s)
immediately`below'thenetworklayerin
theprotocolstack.
ifSpeed .1.3.6.1.2.1.2.2.1.5 Gauge RO Anestimateoftheinterface'scurrent
bandwidthinbitspersecond.Forinterfaces
whichdonotvaryinbandwidthor
for
thosewherenoaccurateestimationcanbe
made,thisobjectshouldontainthe
nominalbandwidth.
ifPhysAddress .1.3.6.1.2.1.2.2.1.6 Phys‐Address RO T heinterface'saddressattheprotocol
layerimmediately`below'thenetwork
layerintheprotocolstack.Forinterfaces
whichdonothavesuchanaddress(e.g.,a
serialline),thisobjectshouldcontainan

octetstringofzerolength.
ifAdminStatus .1.3.6.1.2.1.2.2.1.7 Integer RW Thedesiredstateoftheinterface.The
testing(3)stateindicatesthatno
operationalpacketscanbepassed.
ifOperStatus .1.3.6.1.2.1.2.2.1.8 Integer RO Thecurrentoperationalstat eofthe
interface.Thetesting(3)stateindicates
thatnooperationalpack etscanbepassed.
ifInOctets .1.3.6.1.2.1.2.2.1.10.x Counter RO Thetotalnumberofoctetsreceivedonthe
interface,includingframingcharacters.
ifInUcastPkts .1.3.6.1.2.1.2.2.1.11.x Counter RO Thenumberofsubnetwork‐unicastpackets
deliveredtoahigher‐layerprotocol.
ifInNUcastPkts .1.3.6.1.2.1.2.2.1.12.x Counter RO Thenumberofnon‐unicast(i.e.,
subnetwork‐broadcastorsubnetwork‐
multicast)packetsdeliveredtoahigher‐
layerprotocol.
ifInErrors .1.3.6.1.2.1.2.2.1.14.x Counter RO Thenumberofinboundpacketsthat
containederrorspreventingthemfrom
beingdeliverabletoahigher‐layer
protocol.