ONLINE HELP SOPAS
LECTOR®620
Contents
8013778/Y269/2013-11-27 © SICK AG · Germany · All rights reserved · Subject to change without notice 7
5.8.4.1.1 Check min. number of valid codes..........................................79
5.8.4.1.2 Check max. number of valid codes .........................................79
5.8.4.2 Evaluation conditions......................................................................79
5.8.5 Match code ...............................................................................................80
5.8.5.1 Matchcode Teach-in 1 ....................................................................80
5.8.5.1.1 Activating teach-in mode .........................................................80
5.8.5.1.2 Or teach-in via function buttons..............................................81
5.8.5.1.3 Teach-in stop by........................................................................81
5.8.5.1.4 Teach-in condition ....................................................................81
5.8.5.1.5 Inverting a condition.................................................................81
5.8.5.1.6 Teach-in code content..............................................................81
5.8.5.1.7 Teach-in code ID (type) ............................................................81
5.8.5.1.8 Teach-in code length................................................................82
5.8.5.2 Match-code Teach-in 2 (Additional) ...............................................82
5.8.5.2.1 Activate teach-in mode ............................................................82
5.8.5.2.2 Teach-in stop by........................................................................83
5.8.5.2.3 Teach-in condition ....................................................................83
5.8.5.2.4 Invert condition.........................................................................83
5.8.5.2.5 Teach-in code content..............................................................83
5.8.5.2.6 Teach-in code ID (type) ............................................................83
5.8.5.2.7 Teach-in code length................................................................83
5.8.5.3 General Match code teach-in - settings.........................................84
5.8.5.3.1 Start teach-in ............................................................................84
5.8.5.3.2 Allowed code types...................................................................84
5.8.5.3.3 Code configuration ...................................................................84
5.8.5.3.4 Save permanent.......................................................................85
5.8.6 Filters/Sorters for the output formatting................................................85
5.8.6.1 Filters/Sorters for Output Format1................................................85
5.8.6.2 Filters/Sorters for Output Format2................................................91
5.8.7 Output format ...........................................................................................96
5.8.7.1 Output format 1...............................................................................96
5.8.7.2 Output format 2............................................................................ 102
5.8.7.3 Heartbeat format.......................................................................... 107
5.8.8 Serial input data.................................................................................... 108
5.8.8.1 Data forwarding............................................................................ 108
5.8.8.1.1 Rx header............................................................................... 108
5.8.8.1.2 Rx terminator ......................................................................... 108
5.8.8.1.3 Target interface ..................................................................... 108
5.8.8.1.4 Tx header ............................................................................... 109
5.8.8.1.5 Tx terminator.......................................................................... 109
5.8.8.2 Auxiliary input/Auxiliary read result ............................................ 109
5.8.8.2.1 Rx header............................................................................... 109
5.8.8.2.2 Rx terminator ......................................................................... 109
5.8.8.2.3 Bar code type......................................................................... 109
5.8.8.2.4 Code IDs for bar codes.......................................................... 110
5.8.8.3 EDS text element in output format / element output format ... 110
5.8.8.3.1 Rx header............................................................................... 111
5.8.8.3.2 Rx terminator ......................................................................... 111
5.8.8.3.3 Default text ............................................................................ 111
5.8.9 Application counters ............................................................................. 111
5.8.9.1 Application counter ...................................................................... 111
5.8.9.1.1 Resetting counter statuses................................................... 112
5.8.9.1.2 Saving current counter statuses .......................................... 112
5.8.9.1.3 Application counter ............................................................... 112
5.8.9.1.4 Value ...................................................................................... 113
5.8.9.1.5 Saving the counter state permanently................................. 113
5.9 Analysis tools................................................................................................ 113
To Next Page
Loading...
Need help?
General