Siemens SIPROTEC 7SJ62 - Page 534

Index
Index-4 7SJ62 Instruction Manual
C53000-G1140-C121-1
No Trip – No Flag 6-164
Nominal Currents 8-6
Nominal Frequency 6-11
Nominal rated values 6-15
Numerical Values 6-4, 6-7
O
Open Breaker Times 6-136
Operating Hours Counter 10-38
Operating Panel 4-5
Operating Serial Interface 4-6
Operating Software A-4
Operator Control Panel 3-5
Optical Communication Interfaces 2-12, 2-16
Optical Fibers 8-16
Order number 9-8
Ordering Information A-2
Ordering Number 3-3, 3-5
Output Indication (OUT) 5-15
Output Relays 10-3
Overcurrent 6-18
Over-Frequency 10-32
Overview of the masking features A-65
Overvoltage Protection 6-111, 6-116
P
Packing 3-2
Panel Flush Mounting 2-2, 8-2, A-6
Panel Surface Mounting 2-14, 8-4, A-8
Password 4-15, 4-33, 6-4
PC Front Interface 10-4
PC Interface at Front 8-15
Performing Configuration 5-21
Phase Overcurrent Protection 6-32, 6-54
Phase Rotation 6-10, 6-147
Plug & Play 3-8
Plug-In Terminals 2-9, 2-10
Polarity of Current Transformers 6-8
Polarity Testing for Ground Fault Protection 8-21
Power Supply 1-4, 10-2
Power Supply Voltage 8-6
Power System Data 4-26
Power System Data 1 6-8
Power System Data 2 6-14
Power-Up 3-3
Preset Configurations 5-28
PROFIBUS 4-3
Profibus Connection 5-43
Profibus DP 4-3
PROFIBUS FMS 4-3
Programmable Logic CFC 4-24
Protective Functions 1-5
R
Rack Mounting 8-3
Reactance Setting 6-15
Rear Service–/Modem– Interface 10-4
Reassembling the Device 9-11
Recognition of Running Condition 6-16
Recording of Event and Fault Data 1-6
Regionalization 6-2
Repairs 9-9
Replacing the Battery 9-4
Replacing the Power Supply Fuse 9-10
Reset Time Characteristics
As Per ANSI 10-15, 10-24
Restoring Factory Settings 6-14
Retrieval of Information 7-2
Retrieving Device Configurations 5-27
Return 9-13
Reverse Interlocking Bus Protection 6-25
Reverse Interlocking for Looped Lines 6-48
Reverse Interlocking Scheme 8-23
Routine Checks 9-3
RS 485 Termination 8-16
Run-Time Properties 5-32
S
SCADA Interface 8-15, 10-5
Sensitive Ground Fault Detection 1-8, 6-73, 10-20
Serial Interfaces 1-3, 4-31, 8-7
Serial Ports 5-41
Service Conditions 10-9
Set points 6-170
Set Status 7-43
Setting Groups 4-27, 6-12, 6-14, 7-32, 8-5
Setting Limit Values 7-22
Settings A-17
Short Circuit Links 2-7, A-4
SIMATIC CFC 4 A-5
Singe Point Indication (SP) 5-15
Single-Shot Reclosing 6-131
Software Monitoring 6-149
Source 5-14
Spontaneous Annunciations 7-11
Spontaneous Messages 6-162, 6-168, 7-6
www . ElectricalPartManuals . com