Yamaha 200A - Page 274

60H5E11
A.
Adjusting the carburetor pickup timing ..... 3-15
Adjusting the carburetor
synchronization ...................................... 3-13
Adjusting the choke solenoid ................... 3-16
Adjusting the engine idle speed ............... 3-14
Adjusting the ignition timing ....................... 3-8
Adjusting the throttle link and the throttle cable
operation ................................................ 3-16
Adjusting the trim sensor cam.................. 7-47
After test run ............................................ 1-17
Air intake system........................................ 9-9
Applicable models ...................................... 1-5
Assembling the carburetor ....................... 4-13
Assembling the clamp brackets ............... 7-46
Assembling the drive shaft
housing ......................................... 6-19, 6-48
Assembling the forward gear ................... 6-20
Assembling the fuel pump.......................... 4-8
Assembling the lower unit (counter rotation
model) .................................................... 6-50
Assembling the lower unit (regular rotation
model) .................................................... 6-21
Assembling the piston and connecting
rod .......................................................... 5-35
Assembling the power trim and tilt unit .... 7-36
Assembling the propeller shaft and propeller
shaft assembly ....................................... 6-44
Assembling the propeller shaft
assembly ................................................ 6-16
Assembling the propeller shaft housing
assembly ................................................ 6-14
Assembling the PTT motor....................... 7-25
Assembling the reservoir and gear pump
unit ......................................................... 7-30
Assembling the reverse gear ................... 6-49
Assembling the upper case...................... 7-12
B.
Backlash (counter rotation model) ........... 6-61
Backlash (regular rotation model) ............ 6-31
Bleeding the power trim and tilt unit ......... 7-39
Bleeding the power trim and tilt unit
(Built-in).................................................. 7-15
Bottom Cowling .......................................... 7-2
Bracket unit .............................................. 9-14
Break-in.................................................... 1-17
C.
Carburetor .................................................. 4-9
Changing the gear oil ............................... 3-19
Charging system ...................................... 8-20
Index
i-1
Checking and replacing the spark plug caps
(Standard type) ........................................ 8-9
Checking the anodes ............................... 3-21
Checking the armature............................. 8-18
Checking the battery ....................... 1-14, 3-21
Checking the brushes .............................. 8-19
Checking the carburetor ........................... 4-12
Checking the carburetor
synchronization ...................................... 3-12
Checking the CDI unit .............................. 8-13
Checking the charge coil.......................... 8-12
Checking the choke solenoid ................... 8-19
Checking the compression pressure.......... 5-2
Checking the connecting rod ................... 5-33
Checking the cooling water passage ......... 3-5
Checking the crankshaft........................... 5-33
Checking the cylinder block ..................... 5-30
Checking the drive shaft.................. 6-21, 6-49
Checking the drive shaft housing .... 6-19, 6-48
Checking the electrical components .......... 8-2
Checking the engine start switch and engine
stop switch, engine shut-off switch......... 1-16
Checking the forward gear ....................... 6-20
Checking the fuel filter......................... 3-4, 4-6
Checking the fuel joint................................ 4-6
Checking the fuel joint and fuel hoses (fuel
joint - to - carburetor) ............................... 3-3
Checking the fuel pump ............................. 4-7
Checking the fuel system ......................... 1-14
Checking the fuse .................................... 8-15
Checking the gear oil ............................... 1-14
Checking the gear oil level ....................... 3-19
Checking the gearshift and throttle
operation ................................................ 1-15
Checking the gearshift operation ............. 3-17
Checking the hour meter............................ 3-3
Checking the hydraulic pressure of the power
trim and tilt unit....................................... 7-18
Checking the ignition coil ......................... 8-11
Checking the ignition spark gap ................. 8-9
Checking the ignition timing ....................... 3-7
Checking the ignition timing
(with timing light) ...................................... 3-6
Checking the lighting coil ......................... 8-21
Checking the lower unit
(for air leakage) ...................................... 3-20
Checking the outboard motor mounting
position................................................... 1-14
Checking the pilot water outlet ................. 1-16
Checking the pinion gear ................ 6-21, 6-49
Checking the piston ................................. 5-31
Checking the plug cap
(with resister type).................................. 8-10