ABB DCS550 - Page 300

316 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

300

Fault tracing

3ADW000379R0501 DCS550 Manual e e

7-segment

display

Text on DCS

Control Panel

and DWL

Definition / Action

Alarm-

word

Alarm is

active when

Alarmlevel

bit 13

A304

304 APAlarm4

User defined alarm by AP

9.08,

bit 14

always

4

A305

305 APAlarm5

User defined alarm by AP

9.08,

bit 15

always

4

A4xx

4xx UserAlarmxx

Disappearing user alarm

-

-

Table of Contents

DCS550 Manuals2
- Chapter Overview3
- Usage of Warnings and Notes3
- Installation and Maintenance Work3
Safety Instructions3
- Grounding4
- Mechanical Installation5
- Operation5
Table of Contents6
Introduction8
- DC Drives Worldwide Service Network9
- General9
- Overview Main Circuit and Control11
- Environmental Conditions12
  - North American Standards13
  - Regulatory Compliance13
- Type Code13
- Voltage and Current Ratings14
- Dimensions and Weights16
ABB Drive Service9
The DCS5509
Mechanical Installation19
- Cabinet Installation20
Planning the Electrical Installation21
- Drive Connection and Wiring Example22
- Installation Components24
- ① Line Reactors (L1)24
- ② Semiconductor Fuses (F1)25
- ③ EMC Filters (E1)25
  - Generation of Control and Monitoring Signals28
  - Generation of on / off and Start / Stop Commands28
- ④ Auxiliary Transformer (T2) for Converter Electronics and Fan28
- ⑤ Start, Stop and E-Stop Control28
  - Fan Assignment for DCS55029
  - Fan Data for DCS55029
- ⑥ Cooling Fans29
- Cabling30
- Power Connections35
  - Supply Voltage35
  - Cross-Sectional Areas - Tightening Torques36
- Drive Interfaces37
- Installation Checklist39
Electrical Installation34
Electronic Board Details40
- Terminal Locations40
- Table of Used Boards41
- Control Board SDCS-CON-F42
- Power Interface Board SDCS-PIN-F45
- Integrated Field Exciters SDCS-BAB-F01 and SDCS-BAB-F0247
  - Circuit Diagram48
  - Typical Armature Circuit Diagram for Module Sizes F3 and F4 Using SDCS-PIN-F and SDCS-BAB-F0249
Accessories50
- ① Line Reactors (L1)50
- ② Semiconductor Fuses (F1)56
- List of Available EMC Filters58
- ③ EMC Filters (E1)58
- ④ Auxiliary Transformer (T2) for Converter Electronics and Fans58
Start-Up59
- Commissioning59
- Macros63
- Start / Stop Sequences74
- Start the Drive74
Firmware Description74
- Excitation75
- DC-Breaker77
- Application Example of Dynamic Breaking78
- Dynamic Braking78
- Digital I/O Configuration80
- Analog I/O Configuration84
Serial Field Bus Communication88
- Canopen Communication with Fieldbus Adapter RCAN-0188
- Controlnet Communication with Fieldbus Adapter RCNA-0192
- Devicenet Communication with Fieldbus Adapter RDNA-0195
  - Rdna-01 - Dcs55095
  - Parameter Setting Example 2 Using User Specific Assembly96
- Ethernet/Ip Communication with Fieldbus Adapter RETA-0198
- Parameter Setting Example Using Ethernet/Ip ABB Drives Communication Profile98
- Modbus (RTU) Communication with Fieldbus Adapter RMBA-01102
- Modbus/Tcp Communication with Fieldbus Adapter RETA-01104
- Parameter Setting Example Using Modbus/Tcp104
- Profibus Communication with Fieldbus Adapter RPBA-01105
- Profinet Communication with Fieldbus Adapter RETA-02109
- Data Set Table110
- Switch on Sequence110
- How to Build the Program111
- How to Connect AP with the Firmware111
AP (Adaptive Program)111
- Block Parameter Set of Block 1112
- Block Inputs113
- Function Blocks, General Rules113
- How to Control the Execution of AP113
- Constant as an Integer Input114
- How to Select the Input114
- Parameter Value as an Integer Input114
- Constant as a Boolean Input115
- Change to Edit Mode116
- Dwl Ap116
- Function Blocks120
- Winder Blocks132
- Winder Macros139
- How the Block Handles the Input115
- Parameter Value as a Boolean Input115
Signal and Parameter List153
- Signal Groups List153
- Parameter Groups List154
  - Sample of Parameters155
  - Physical Actual Values156
- Signals156
- Parameters181
Display Overview270
DCS Control Panel270
Output Mode271
Fault Tracing276
- Converter Protection276
- Motor Protection279
- Display of Status, Fault Messages and Error Codes285
  - General Messages286
  - Power-Up Errors (E)286
- Fault Signals (F)286
- Alarm Signals (A)294
- Notices301
- Drive Configuration with Reduced Components302
Appendix A: Quick Start-Up Diagrams302
- DCS550 Module303
- I/O Connections304
Appendix B: Firmware Structure Diagrams305
Appendix C: Index of Signals and Parameters309

Related product manuals

Preview: ABB DCS550-S01

ABB DCS550 Series

Preview: ABB DCS800

Preview: ABB DCS880

Preview: ABB DCS 400

Preview: ABB DCS880 series

ABB DCS880 series

Preview: ABB DMP Series

Preview: ABB ACS2000 DFE

ABB ACS2000 DFE

ABB DMP 180-4 LD

ABB DriveIT ACH550-UH

Preview: ABB ACS880-04 drive modules

ABB ACS880-04 drive modules