To Next Page

To Previous Page

Section 12 – Power Requirements

12-3

Table 2: SIM Gateway Standby and Alarm Loads

Gateway Unit No. __________ (Maximum 72 Points)

A B AxB C AxC

Device Quantity

Standby

Current (mA)

Total

Standby

Current (mA)

Alarm

Current

(mA)

Total Alarm

Current

(mA)

SIM Door Contact

SIM PIR Motion

SIM Dual Motion

SIM Smoke Detector

SIM Holdup Button

SIM FA Pull Station

SIM

∗

Total Loads of SIM Sensors

(Total alarm load must not exceed 128mA)

Standby Alarm

Horn/Strobe

∗∗ ∗∗

Sounder 472307

10 10

Powered Sensors

Relay

Total Standby and Alarm Loads

on Gateway Trunk

Standby Alarm

SIM Gateway

150 50 5050

Total Gateway Standby and

Alarm Current

Standby Alarm

∗

SIM connected to external contact, powered sensor, self-powered sensor, output SIM, or horn/strobe

∗∗

190mA for bell mode with strobe, 260mA for horn/strobe

Fire Alarm Application Note5
- Code Enforcement5
- Table of Contents6
Conventions Used in this Manual10
Section 111
General Description11
- About the FOCUS 200 PLUS System11
- Prominent Features11
Section 213
Installing the Control Unit13
- About the Control Unit13
- Before Installing the System13
- Mounting the Cabinet14
- Installing the Cabinet Lock14
- Figure 2-1: Installing Cabinet Lock14
- Grade a Mercantile Premises Listing15
- Figure 2-2: Cabinet Attack Resistance Considerations15
- Figure 2-3: Cabinet Door Tamper Wiring15
- Grade a Mercantile Safe and Vault Listing16
- Installing the Control's Circuit Board16
- Figure 2-4: Mounting the PC Board16
Section 317
Installing the Operating Panels17
- About the Operating Panels17
- Installing the Operating Panels18
- Figure 3-1: Details of the Operating Panel Circuit Board18
- Addressing the Operating Panels19
- Operating Panel Program Mode21
- Adjusting the Contrast Level21
Section 423
Basic Hardwired Points23
- About the Hardwired Points23
- Wiring the Hardwired Points24
- Figure 4-1: 2-Wire Smoke Detector Connected to Point 1 (Can also be Connected to Point 2, Terminals 27 and 28)25
- Figure 4-2: 4-Wire Smoke Detector Connections Points 1-826
- Point 8 Bell Box Tamper Configuration27
Section 529
Gateways29
- About the Gateways29
- PID Gateway30
- Figure 5-1: PID Gateway Module32
- Installing the PID Gateway33
- Installing Sensors to the PID35
- Figure 5-2: PID Wiring Connections to System-Powered Sensors38
- Figure 5-3A: Basic Sensor Connections to PID39
- Figure 5-3B: Basic Sensor Connections to PID39
- Figure 5-4: Connections of BA Sensors with Field Wiring Terminals to PID40
- Figure 5-5: Using a PID to Turn on a PA400W Sounder40
- SIM Gateway41
- Figure 5-6: SIM Gateway Module42
- Installing the SIM Gateway43
- Installing SIM and SIM Sensors45
- Figure 5-7: SIM Wiring to System-Powered and Nonpowered Sensors46
- Figure 5-8: Connection for a Gateway Loop Powered SIM Sensor47
- Figure 5-9: SIM Wiring to a Horn and Strobe47
- Figure 5-10: SIM Wiring to a Sensor48
- Figure 5-11: SIM Connections to a Vault Vibration Sensor48
- Figure 5-12: SIM Connections to a 4-Wire/2-Wire Adapter49
- Figure 5-13: Loop Interface Module50
- RF Gateway (472490)51
- Figure 5-14: Loop Interface Module Wiring to Powered Sensor51
- Figure 5-15: Loop Interface Module Wiring to Lacing/Foil and Non-Powered Sensor51
- Installing the RF Gateway52
- Figure 5-16: RF Gateway Wiring Connections52
- Installing the RF Receiver53
- 5800 Series Transmitters54
- Figure 5-17: RF Receiver DIP Switch Settings54
- Gateway Off-Normal Conditions56
Section 657
Bell Outputs and Auxiliary Relay57
- About the Bell Outputs and Auxiliary Relay57
- Output Functions58
- Installing the External Sounders60
- Figure 6-1: External Sounder Connections to the Bell Outputs62
- Programming the Bell Outputs63
- Figure 6-2: External Sounder Connections to the Auxiliary Relay63
Section 765
System Communication65
- About the System Communication65
- Connecting the Telephone Lines66
- Figure 7-1: Installing the 472402A Backup Dialer67
- Description of ADEMCO Contact ID Format68
- Types of Customer Care Center Service72
- Table of CCC Signaling74
- Programming the System Communication Options75
Section 877
AC Communicator Module77
- About the AC Communicator Module77
- Installing the AC Communicator Module77
- Figure 8-1: AC Communicator Module Wiring78
- Figure 8-2: AC Communicator Module Wiring Using AC Telephone Lines79
- Figure 8-3: AC Communicator Module Wiring Using DVACS or RS232 Port79
- Using Multiple AC Communicator Modules80
- Programming for the AC Communicator Module80
- Figure 8-4: AC Communicator Module Wiring Using DC Telephone Lines80
Section 981
J5 Output Triggers81
- About the J5 Output Triggers81
- Types of Output Points81
- Auxiliary Alarm Signaling Equipment84
- Figure 9-1: Configuration of the 7720P to the J5 Output Triggers84
- Figure 9-2: Configuration of the 7830R to the J5 Output Triggers85
- Figure 9-3: Configuration of the 7835C to the J5 Output Triggers85
- Programming the Output Triggers86
- Figure 9-4: Configuration of the 7920SE to the J5 Output Triggers86
Section 1087
Access Control87
- About Access Control87
- Figure 10-1: Access Control Interface Unit (ACIU)89
- Installing the Access Control Interface Unit90
- Using Readers, Keyloks, and Operating Panels92
- Figure 10-2: Typical Installation Using Card Reader or Keyreader96
- Figure 10-3: Typical Installation Using a Keylok96
- Figure 10-4: Modifying ACIU for Operation with Dorado 7401 or 7901 Card Reader97
- Figure 10-5: Wiring Connections for a Manual Access Pushbutton or Exit Pushbutton98
- Access Control Options99
- Maintenance of the Access Control Interface Unit105
Section 11111
History Log111
- About the History Log111
- Installing the Printer Interface Unit111
- Figure 11-1: Printer Interface Unit112
- Displaying and Printing the History Log113
Section 12119
Power Requirements119
- About Powering the FOCUS 200 PLUS119
- Providing Adequate Voltage for each Gateway and Operating Panel120
- Figure 12-3: Determining the Voltage Drop on the RS-485 Bus125
- Determining Maximum Length of Gateway Trunk Cable126
- Figure 12-4: Determining Maximum Length of Quad Trunk for PID Gateway (no Horn/Strobes)126
- Determining the Control Unit Power Supply Load127
- Figure 12-5: Determining the Maximum Length of Quad Trunk for SIM/PID Gateway with Horn/Strobes127
- Determining the Size of the Standby Battery131
- Installing a Power Supply133
- Connecting AC Power and Earth Ground to the Control Unit133
- Installing the Standby Battery135
- Powering up the Control Unit136
Section 13137
Input and Output Point Types137
- About the Input and Output Point Types137
- Input Point Types137
- Output Point Types144
Section 14149
Programming149
- About Programming the System149
- Mechanics of Programming150
- Programming Names for the BA Groups150
- Programming Point Data151
- Programming the BA Groups' Turn-Off Data154
- Programming the System Communication Options155
Section 15157
Scheduling157
- About Scheduling157
- Permanent Schedules158
- Temporary Schedules159
- Holiday Schedules160
- Ambush Schedule160
- Scheduling Options161
Section 16163
Downline Loading163
- About Downline Loading163
- Programming the Control Unit for Downline Loading163
- Downline Loading the Customized Data164
- Verifying the Downline Loaded Data165
Section 17167
Real-Time Clock167
- About the Real-Time Clock167
- Setting the Time and Date167
- Setting Daylight Saving Time168
Section 18169
ID Codes169
- About the ID Codes169
- Service Code170
- Fire Marshall Code170
- Duress Signal170
- Programming ID Codes171
- Summary of ID Code Capabilities and Privileges172
Section 19175
System Operation175
- About Operating the System175
- Figure 19-1: Operating Panel175
- Action Menus176
- Operating Panel Modes179
- ID Codes180
- Control Unit and BA Group Options181
- Recycling Exit Delay186
- Alarm/Trouble Memory187
Section 20189
Testing the System189
- About Testing the System189
- Operating Panel Tests189
- Local Tests190
- Transmission Tests191
- Testing the Printer192
- Finishing the Installation192
- Instructing the Customer192
Section 21193
Specifications193
- Electrical/Mechanical Specifications193
- Installation Criteria194
- Approvals195
- Access Control Interface Unit195
Section 22197
Equipment197
- Basic System Equipment197
- SIM Sensors201
Index205
Limitations of this Alarm System213

Brand	ADT
Model	Focus 200 Plus
Category	Security System
Language	English

ADT Focus 200 Plus Installation And Setup Guide

Table of Contents

Other manuals for ADT Focus 200 Plus

Questions and Answers:

ADT Focus 200 Plus Specifications

Related product manuals