Draytek Vigor2860 - Page 736

Vigor2860 Series User’s Guide
722
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
a
a
d
d
s
s
l
l
t
t
x
x
p
p
c
c
t
t
/
/
a
a
d
d
s
s
l
l
r
r
x
x
p
p
c
c
t
t
This command allows the user to adjust the percentage of data transmission
(receiving/transmitting) for QoS application.
S
S
y
y
n
n
t
t
a
a
x
x
adsl txpct [auto:percent]
adsl rxpct [auto:percent]
Parameter Description
auto It means auto detection of ADSL transmission packet.
percent Specify the percentage of ADSL transmission packet.
Available range is 10-100.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> adsl txpct auto
% tx percentage : 80
> adsl txpct 75
% tx percentage : 75
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
a
a
d
d
s
s
l
l
s
s
t
t
a
a
t
t
u
u
s
s
This command is used to display current status of ADSL setting.
S
S
y
y
n
n
t
t
a
a
x
x
adsl status [more | counts | hlog | qln | snr | bandinfo | olr]
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> adsl status
--------------------------- ATU-R Info (hw: annex A, f/w: annex Unknown) -----
Running Mode : T1.413 State : TRAINING
DS Actual Rate : 0 bps US Actual Rate : 0 bps
DS Attainable Rate : 0 bps US Attainable Rate: 0 bps
DS Path Mode : Fast US Path Mode : Fast
DS Interleave Depth : 0 US Interleave Depth: 0
NE Current Attenuation : 0 dB Cur SNR Margin : 0 dB
DS actual PSD : 0. 0 dB US actual PSD : 0. 0 dB
ADSL Firmware Version : 05-04-08-00-00-06
--------------------------- ATU-C Info ---------------------------------
Far Current Attenuation : 0 dB Far SNR Margin : 0 dB
CO ITU Version[0] : 00000000 CO ITU Version[1] : 00000000
DSLAM CHIPSET VENDOR : < ADI >
>
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
a
a
d
d
s
s
l
l
p
p
p
p
p
p
This command can set the Internet Access mode for the router.
S
S
y
y
n
n
t
t
a
a
x
x
adsl ppp [ ? | pvc_no vci vpi Encap Proto modu acqIP idle [Username Password]
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n