Draytek Vigor2860 - Page 745

Vigor2860 Series User’s Guide
731
> adsl inventory cpe
G.994 vendor ID : 0XB5004946544E5444
G.994.1 country code : 0XB500
G.994.1 provider code : IFTN
G.994.1 vendor info : 0X5444
System vendor ID : 0XB5004946544E0000
System country code : 0XB500
System provider code : IFTN
System vendor info : 0X000
Version number : 3.8.2_RC4a_STD
Version number(16 octets) : 0X332E382E325F524334615F5354440000
Self-test result : PASS
Transmission mode capability : 0X40004004C010400
>
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
v
v
d
d
s
s
l
l
s
s
t
t
a
a
t
t
u
u
s
s
This command is used to display current status of VDSL setting.
S
S
y
y
n
n
t
t
a
a
x
x
vdsl status [more | counts | hlog | qln | snr | bandinfo | olr]
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> vdsl status
---------------------- ATU-R Info (hw: annex A, f/w: annex A/B/C) -----------
Running Mode : State : TRAINING
DS Actual Rate : 0 bps US Actual Rate : 0 bps
DS Attainable Rate : 0 bps US Attainable Rate : 0 bps
DS Path Mode : Fast US Path Mode : Fast
DS Interleave Depth : 0 US Interleave Depth : 0
NE Current Attenuation : 0 dB Cur SNR Margin : 0 dB
DS actual PSD : 0. 0 dB US actual PSD : 0. 0 dB
NE CRC Count : 0 FE CRC Count : 0
NE ES Count : 0 FE ES Count : 0
Xdsl Reset Times : 0 Xdsl Link Times : 0
ITU Version[0] : b5004946 ITU Version[1] : 544e0000
VDSL Firmware Version : 05-04-08-00-00-06
Power Management Mode : DSL_G997_PMS_NA
Test Mode : DISABLE
---------------------- ATU-C Info ---------------------------------
Far Current Attenuation : 0 dB Far SNR Margin : 0 dB
CO ITU Version[0] : 00000000 CO ITU Version[1] : 00000000
DSLAM CHIPSET VENDOR : < unknown >
>
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
v
v
d
d
s
s
l
l
i
i
d
d
l
l
e
e
This command can make the router accessing into the idle status. If you want to invoke the
router again, you have to reboot the router by using “reboot” command.
S
S
y
y
n
n
t
t
a
a
x
x
vdsl idle [on | tcpmessage | tcpmessage_off]
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
on DSL is under test mode.
DSL debug tool mode is off.