Draytek Vigor2860 - Page 746

Vigor2860 Series User’s Guide
732
tcpmessage DSL debug tool mode is on.
tcpmessage_off DSL debug tool mode is off.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> vdsl idle on
% DSL is under [IDLE/QUIET] test mode.
% DSL debug tool mode is off.
> vdsl idle tcpmessage
% Set DSL debug tool mode on. Please reboot system to take effect.
> vdsl idle tcpmessage_off
% Set DSL debug tool mode off. Please reboot system to take effect.
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
v
v
d
d
s
s
l
l
d
d
r
r
i
i
v
v
e
e
r
r
m
m
o
o
d
d
e
e
This command is useful for laboratory to measure largest power of data transmission. Please
follow the steps below to set vdsl drivermode.
1. Please connect dsl line to the DSLAM.
2. Waiting for dsl SHOWTIME.
3. Drop the dsl line.
4. Now, it is on continuous sending mode, and vdsl2/2+ led is always ON.
5. Use 'vdsl reboot' to restart dsl to normal mode.
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
v
v
d
d
s
s
l
l
r
r
e
e
b
b
o
o
o
o
t
t
This command can reboot the DSL router.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> vdsl reboot
% Adsl is Rebooting...
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
v
v
d
d
s
s
l
l
a
a
n
n
n
n
e
e
x
x
This command can display the annex interface of this router.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> vdsl annex
% hardware is annex A.
% ADSL modem code is annex A
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
v
v
d
d
s
s
l
l
s
s
h
h
o
o
w
w
b
b
i
i
n
n
s
s
This command can display the allocation for each Bin (Tone) SNR, Gain, and Bits.
S
S
y
y
n
n
t
t
a
a
x
x
vdsl showbins [startbin endbin | up]
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
startbin The number is between 0 ~ 4092.
endbin The number is between 4 ~ 4095.
up Show upstream information.
E
E
x
x
a
a
m
m
p
p
l
l
e
e